MIMAKI Kebab MKII Скачать руководство пользователя

Страница: 52 / 56

Maintenance

Cleaning the roller shafts

Clean the roller shafts when they become dirty with ink using the procedure described below to ensure that this
product can be continually used over a long period of time.

Cover the area below the roller to be
cleaned with a paper towel and attach a
cover on the origin mark sensor.

• This will prevent the cleaning liquid from coming into contact

with the cover and the origin mark sensor.

Rotate the roller shaft until the rubber
part that is dirty with ink comes into
view.

• Pinch the metal part of the roller shaft with your fingers and

slowly rotate the roller.

Rub the part that is dirty with ink for-
wards and backwards with a BEMCOT
that has been dipped in cleaning liquid.

• Hold the roller with your fingers when rubbing it with a BEM-

COT so that it does not rotate.

• Take care so as not to rub too hard.
• Take care so as not to have the cleaning liquid come into

contact with parts other than the roller shaft, such as the ori-
gin mark sensor, and the cover.

• Make sure to put on goggles and gloves before cleaning. (Use the goggles and gloves that come as

accessories with printer).

• Make sure that the cleaning liquid does not come into contact with your skin.
• Remove the Kebab MkII system from the printer body before cleaning.

Tools

• Glove

• Goggles

• Paper towel

• BEMCOT (A101437) or a maintenance cloth (SPC-0574)
• F-200 / LF-200 Washing Liquid 100 (SPC-0568)

Rotate with

Rub forwards
and backwards

Содержание Kebab MKII

























































Результаты поиска

Содержание Kebab MKII

Отзывы:

Похожие инструкции для Kebab MKII

Бренды по названию

Популярные бренды

MIMAKI Kebab MKII, Руководство по эксплуатации

Результаты поиска

Содержание Kebab MKII

Отзывы:

Похожие инструкции для Kebab MKII

Бренды по названию

Популярные бренды