MIMAKI Kebab MKII Скачать руководство пользователя | Manualshive

Страница: 3 / 56

background image

For safe operation

3

For safe operation

Symbols

Symbols are used in this Operation Manual for safe operation and for prevention of damage to the machine. The
indicated sign is different depending on the content of caution.
Symbols and their meanings are given below. Please follow these instructions as you read this manual.

Contents

Failure to observe the instructions given with this symbol can result in death or serious injuries to
personnel. Be sure to read it carefully and use it properly.

Failure to observe the instructions given with this symbol can result in injuries to personnel or dam-
age to property.

Important notes in use of this machine are given with this symbol. Understand the notes thoroughly
to operate the machine properly.

Useful information is given with this symbol. Refer to the information to operate the machine prop-
erly.

Indicates the reference page for related contents.

The symbol “

” indicates that the instructions must be observed as strictly as the CAUTION

instructions (including DANGER and WARNING instructions). A sign representing a precaution (the
sign shown at left warns of hazardous voltage) is shown in the triangle.

The symbol “

” indicates that the action shown is prohibited. A sign representing a prohibited

action (the sign shown at left prohibits disassembly) is shown in or around the circle.

The symbol “

” indicates that the action shown must be taken without fail or the instructions must

be observed without fail. A sign representing a particular instruction (the sign shown at left instructs
to unplug the cable from the wall outlet) is shown in the circle.

«
1
2
3
4
5
...
»

Содержание Kebab MKII

























































Отзывы:

Нет отзывов

Похожие инструкции для Kebab MKII

Бренд: LabelTac Страницы: 2

Бренд: WaxJet Страницы: 131

Бренд: QMS Страницы: 26

Бренд: Grizzly Страницы: 56

Бренд: GCC Technologies Страницы: 97

Бренд: Muratec Страницы: 6

Magicolor 4650DN

Бренд: Konica Minolta Страницы: 260

PG 2028 SPECIAL

Бренд: Olivetti Страницы: 104

Бренд: Oki Страницы: 4

Aficio SG 7100DN

Бренд: Ricoh Страницы: 359

Бренд: XYZ Printing Страницы: 33

Printpix NC-400D

Бренд: FujiFilm Страницы: 47

ApeosPort C5570

Бренд: Fuji Xerox Страницы: 290

Бренд: L-Mark Страницы: 62

GG IMAGE P4100 Series

Бренд: G&G Страницы: 102

WorkForce Pro WF-C8190DTWC

Бренд: Epson Страницы: 162

WorkForce Pro WP-4095 DN

Бренд: Epson Страницы: 2

WorkForce Pro WP-4532

Бренд: Epson Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды