MIMAKI Kebab MKII Скачать руководство пользователя | Manualshive

Страница: 2 / 56

background image

Foreword

2

Foreword

Thank you very much for purchasing Kebab MkII system/Kebab MkII L system this time.
Kebab MkII system/Kebab MkII L system is a dedicated system to print any design you like on cylindrical work.
Fully read this manual and make use of it in drawing to suit the customer’s needs.

DISCLAIMER OF WARRANTY

THIS LIMITED WARRANTY OF MIMAKI SHALL BE THE SOLE AND EXCLUSIVE WARRANTY AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS, AND MIMAKI NEITHER ASSUMES NOR AUTHORIZES
DEALER TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY OR MAKE ANY OTHER WARRANTY
OR MAKE ANY OTHER WARRANTY IN CONNECTION WITH ANY PRODUCT WITHOUT MIMAKI’S PRIOR
WRITTEN CONSENT.
IN NO EVENT SHALL MIMAKI BE LIABLE FOR SPECIAL, INCIDNETAL OR CONSEQUENTIAL DAMAGES OR
FOR LOSS OF PROFITS OF DEALER OR CUSTOMERS OF ANY PRODUCT.

Requests

• This Operation Manual has been carefully prepared for your easy understanding, however, please do not hesitate to

contact a distributor in your district or our office if you have any inquiry.

• Description contained in this Operation Manual are subject to change without notice for improvement.

• Unauthorized reproduction of any portion of this document is strictly prohibited.

© 2016 MIMAKI ENGINEERING Co., Ltd.

Interference to televisions and radios

The product described in this manual generates low radio waves while it is in operation. The product can interfere
with radios and televisions if set up or commissioned under improper conditions. The product is not guaranteed
against any damage to specific-purpose radios and televisions.
The product’s interference with your radio or television will be checked by turning on/off the power switch of the
product. In the event that the product is the cause of interference, try to eliminate it by taking one of the following cor-
rective measures or taking some of them in combination.

• Change the direction of the receiving antenna or the feeder of your radio/television.
• Move the receiver away from the product.
• Plug the power cord of this machine into an outlet which is isolated from power circuits connected to the television set

or radio.

• Kebab MkII is an option of UJF-3042 MkIIseries and Kebab MkII L is an option of UJF-6042 MkIIseries and

UJF-7151 Plus series. Fully read the instruction manual of printers together with this manual.

«
1
2
3
4
...
»

Содержание Kebab MKII

























































Отзывы:

Нет отзывов

Похожие инструкции для Kebab MKII

Бренд: Qls Страницы: 53

Бренд: Xerox Страницы: 36

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 3

Бренд: Tektronix Страницы: 286

Бренд: Star Страницы: 82

Бренд: Partex Страницы: 12

Бренд: Lexmark Страницы: 57

Бренд: Oki Страницы: 94

4400B - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 24

Бренд: Ricoh Страницы: 37

Бренд: Konica Minolta Страницы: 12

Бренд: Mayku Страницы: 2

Бренд: Nashuatec Страницы: 177

1235N - Phaser Color Laser Printer

Бренд: Tektronix Страницы: 240

Бренд: 3D Systems Страницы: 103

Бренд: Sharp Страницы: 63

Бренд: Sharp Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды