Milnor E-P Plus Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 92

Milnor E-P Plus Скачать руководство пользователя страница 28

22

Pellerin Milnor Corporation

2.3.3

How to Add or Change a Formula (Option 1)

BNCJUP03.C01 0000191875 C.2 D.2 B.3 1/2/20 1:16 PM Released

Milnor

®

E-P Plus

®

washer-extractors have the capacity for a maximum of 30 formulas.

2.3.3.1

What are Formulas, Steps, and Decisions?

BNCJUP03.C02 0000191873 C.2 D.2 B.3 1/2/20 1:16 PM Released

A formula includes all the procedures that the machine does automatically. These procedures start
when you put a load in the machine. The procedures stop when the machine completes all opera-
tions. In some models, there is an alarm at the end of a formula

Different types of steps make formulas. You set values for each step when you write the formula.

1. Set a bath step or an extract step.

2. Set the values in the step.

Bath steps can turn the basket, open the water valves, and put chemicals in the machine. When
the machine completes all the necessary procedures in a step, the subsequent step starts. The for-
mula stops and the alarm comes on when the last step stops.

Each step includes several

programming decisions

. You must answer the questions to build the

wash formula. You must usually choose one answer from a list. For example, the water level deci-
sion in a bath step can be answered with either “1” for low level or “2” for high level. Other pro-
gramming decisions, such as step time and bath temperature, require you to enter a value within a
range of values.

The user interface uses similar procedures to create a new formula and for changing an existing
formula. Both procedures are detailed below, in

2.3.3.4: Create a New Formula, page 24

and

2.3.3.6: Change an Existing Formula, page 25

. The control system tells you whether the selected

formula exists.

2.3.3.2

About the Help Screens

BNCJUP03.C03 0000191932 C.2 D.2 B.3 1/2/20 1:16 PM Released

Display or Action

Explanation

03

T

MMQFFFHC LSCWSS*

01

0

000----- -------

This example shows

Page A

of the programming menu, with the

cursor at the first decision (

T

=Type of Step).

03 T TYPE OF STEP
01

0

END FORMULA

This is a typical programming

help screen

. The display will auto-

matically show a help screen if you do not make a correct entry in
four seconds or less.
Accepts the selected value for the current decision and advances
the cursor to the next decision, regardless of the status of the help
screen.
At either

Page A

or

Page B

, this keystroke displays the formula

and step name for the selected step, if the display has not shown a
help screen.

MODIFYING
FORMULA 03 - STEP 01

This example shows a typical display of the formula name and the
step name.

«
...
26
27
28
29
30
...
»

Содержание E-P Plus





























































































Отзывы:

Нет отзывов