Milnor E-P Plus Скачать руководство пользователя страница 27

Страница: 27 / 92

Pellerin Milnor Corporation

2.3.1

How to Avoid Data Loss

BNCJHP02.C02 0000192162 C.2 D.2 A.7 1/2/20 1:16 PM Released

CAUTION:

Avoid Corrupting Formula Data —

Never turn the

Run/Program key-

switch

from the

Program

position to the

Run

position unless the display

says

OK Turn Key to Run

�

Failure to follow this direction will result in the loss of all formula

modifications entered during the current programming session. Formulas
not modified during this session will not be affected.

CAUTION:

Avoid Corrupting Configuration Data —

Never shut off machine power,

turn off the

Master switch

, or press the

Emergency Stop button

to exit

the

Program

mode.

�

Once the

Configure

menu has been accessed, all configure decisions

must be confirmed by pressing the

Next button

(

) before another action

can be taken.

�

Failure to follow this direction will result in corruption of machine memory.

Use the following procedures to clear corrupted formula and configuration memory and restore
valid data.

Display or Action

Explanation

CHECKSUM ERROR

This display indicates that all memory will be cleared.

The ma-

chine controller must be reconfigured and any new formulas
or modifications to standard formulas must be re-
programmed.

TURN KEY TO PROGRAM

Accesses the first configuration decision.

LANGUAGE ?

First configure decision.

0=ENGLISH

2.3.2

Return to Run Mode (Option 0)

BNCJHP02.C03 0000192161 C.2 D.2 A.7 1/2/20 1:16 PM Released

Option 0

allows for a safe return from the

Program

mode to the

Formula

menu, preserving any

changes that were made during the programming session and maintaining the integrity of pro-
gramming and configuration data.

Display or Action

Explanation

PROGRAM

OK TURN KEY TO RUN

This is

Option 0

of the

Program

menu. From this display, return

to the

Formula

menu or select another available menu option.

Returns to

Run mode

(

Formula

menu)

Scrolls the available choices in the

Program

menu.

Programming

Содержание E-P Plus





























































































Результаты поиска

Содержание E-P Plus

Отзывы:

Milnor E-P Plus, Справочник, Страница: 27 / 92

Результаты поиска

Содержание E-P Plus

Отзывы: