Milnor E-P OneTouch Скачать руководство пользователя страница 6

4

Pellerin Milnor Corporation

2 Normal Operation

BNCOUO01 / 2018253

BNCOUO01

0000189435

A.4

1/2/20 1:25 PM

Released

2.1

E-P OneTouch

®

Operation

BNCOUO01.C01 0000189471 A.5 A.4 1/2/20 1:25 PM Released

2.1.1

Instructions for Normal Operation

BNCOUO01.C02 0000189470 A.5 A.4 1/2/20 1:25 PM Released

2.1.1.1

Load the Machine

BNCOUO01.T01 0000189469 A.5 A.4 1/2/20 1:25 PM Released

1. If the loading door is closed and latched, hold the

Door Unlock

button (

) to unlock the

door while operating the door latch handle with the other hand. If the door does not unlock,
verify that the machine is connected to power and that the wall disconnect is functioning
properly. The machine must have power available to unlock the door.

2. When the door opens, load the machine according to plant guidelines and

Section 2.2 : Deter-

mining Load Size, page 5

.

3. Close the door firmly.

2.1.1.2

Start a Formula

BNCOUO01.C03 0000189482 A.5 A.4 1/2/20 1:25 PM Released

2.1.1.2.1

After a Completed Formula (Normal)

BNCOUO01.C04 0000189481 A.5 A.4 1/2/20 1:25 PM Released

If the previous formula finished normally, simply press the button that matches the formula you
want to run. The selected formula will start immediately if the door is closed. The

Formula Run-

ning

light (

) illuminates and the door locks immediately, and the machine fills with water.

Once the door is locked, the operator must end the formula early (

Section 2.1.2 : How to End a

Formula Early, page 5

or wait for the formula to finish before opening the door.

2.1.1.2.2

After Opening the Door during a Formula

BNCOUO01.C05 0000189480 A.5 A.4 1/2/20 1:25 PM Released

If you ended the previous formula early by opening the door, you must press the

Terminate

but-

ton (

) before you can start the machine again. The

Terminate

button also clears any internal

machine error that might have caused the formula to end early.

2.1.1.3

Unload the Machine

BNCOUO01.C06 0000189512 A.5 A.4 1/2/20 1:25 PM Released

When the formula ends, the

Formula Running

light (

) goes out. Hold the

Door Unlock

button (

) to unlock the door while turning the door latch handle with the other hand.

Содержание E-P OneTouch










Отзывы: