Miller FILTAIR, Руководство пользователя

Страница: 29 / 40

OM-239026 Page 25
7-4. Inspecting Filter And Spark Guard
OM-239026 Page 22
7-4. Inspecting Filter And Spark Guard
245615
! Turn off unit and disconnect
input power cord.
! Do not operate unit without
filter or with dirty (plugged)
filter.
! Clean or replace the filter
when dirty.
! Allow cooling period before
inspecting or replacing filter,
or cleaning particle tray and
spark guard.
! Do not breathe the particles
collected by the fume extrac-
tor. Wear approved safety
equipment
(respirator,
gloves, long sleeve shirt)
when servicing filter and
spark guard. Dispose of
used element and collected
particles according to local,
state, and federal require-
ments.
! Read and understand the
Material Safety Data Sheets
(MSDSs) and the manufac-
turer’s instructions for met-
als, consumables, coatings,
cleaners, and degreasers.
1 Latch
2 Hatch
3 Filter
4 Spark Guard
Release latches and open hatch.
Use filter handles to remove filter.
Clean or replace filter if dirty or
damaged.
Wipe off hatch. Remove particles
from inside of housing.
Remove spark guard (from behind
baffle).
Clean and inspect spark guard
screen. Replace spark guard if
screen wires are broken or missing.
Install spark guard.
Install filter.
Close hatch and secure with
latches.
Tools Needed:
2
3
1
4
OM-222 Page 1
NGO’s
tools/
helmet weldshield faceshield
glasses hairdryer cclamp rpmmeter benchvise
popriveter
oilcan filtersocket hacksaw belttensiongauge sealant_1
snapringpliers linepliers pencil fusepuller mallet scissors
tape
rubbergloves weldgloves earmuffs electrodewrench
pinextractor2
tip_dress
sealant_2 pump pliers
T_allen
pinextractor (141761)
SOAP
bar soap
Liquid soap
Paper Clip
Needle-Nose Vise Grip
Ground Strap
Thermal Compound
Trowel
Chisel
Torx
ear plugs
OM-222 Page 1
NGO’s
tools/
helmet weldshield faceshield
glasses hairdryer cclamp rpmmeter benchvise
popriveter
oilcan filtersocket hacksaw belttensiongauge sealant_1
snapringpliers linepliers pencil fusepuller mallet scissors
tape
rubbergloves weldgloves earmuffs electrodewrench
pinextractor2
tip_dress
sealant_2 pump pliers
T_allen
pinextractor (141761)
SOAP
bar soap
Liquid soap
Paper Clip
Needle-Nose Vise Grip
Ground Strap
Thermal Compound
Trowel
Chisel
Torx
ear plugs
Turn off power and disconnect in-
put power cord.
Do not operate unit without filter or
with dirty (plugged) filter.
Clean or replace the filter when
dirty.
Allow cooling period before in-
specting or replacing filter, or
cleaning particle tray and spark
guard.
Do not breathe the particles col-
lected by the fume extractor. Wear
approved safety equipment (respi-
rator, gloves, long sleeve shirt)
when servicing filter and spark
guard. Dispose of used element
and collected particles according
to
local, state, and federal
requirements.
Do not breathe the particles col-
lected by the fume extractor. Wear
approved safety equipment (respi-
rator, gloves, long sleeve shirt)
when servicing filter and spark
guard. Dispose of used element
and collected particles according
to
local, state, and federal
requirements.
Read and understand the Safety
Data Sheets (SDSs) and the manu-
facturer’s instructions for metals,
consumables, coatings, cleaners,
and degreasers.
1 Latch
2 Hatch
3 Filter
4 Spark Guard
Release latches and open hatch. Use filter
handles to remove filter.
Clean or replace filter if dirty or damaged.
Wipe off hatch. Remove particles from inside
of housing.
Remove spark guard (from behind baffle).
Clean and inspect spark guard screen. Re-
place spark guard if screen wires are broken
or missing.
Install spark guard.
Install filter.
Close hatch and secure with latches.