Miller DYNASTY 200 DX Скачать руководство пользователя страница 65

Страница: 65 / 92

OM-2240 Page 59

SECTION 10

−

SELECTING AND PREPARING TUNGSTEN

ELECTRODE

gtaw5_8/8/03

For additional information, see your distributor for a handbook on the Gas

Tungsten Arc Welding (GTAW) process.Wear clean gloves to prevent

contamination of tungsten electrode.

NOTE

10-1. Selecting Tungsten Electrode

Amperage Range - Gas Type

♦

- Polarity

Electrode Diameter

−

Argon

−

Electrode

Negative/Straight Polarity

−

Argon

−

Electrode

Positive/Reverse Polarity

−

Argon

−

Using

High Frequency

−

Argon

−

Balanced

Wave Using High Freq.

2% Thorium Alloyed

Tungsten (Red Band)

.010”

Up to 25

Up to 20

Up to 15

.020”

15-40

15-35

5-20

.040”

25-85

20-80

20-60

1/16”

50-160

10-20

50-150

60-120

3/32”

135-235

15-30

130-250

100-180

1/8”

250-400

25-40

225-360

160-250

5/32”

400-500

40-55

300-450

200-320

3/16”

500-750

55-80

400-500

290-390

1/4”

750-1000

80-125

600-800

340-525

♦

Typical argon shielding gas flow rates are 15 to 35 cfh (cubic feet per hour).

*Not Recommended.

The figures listed are intended as a guide and are a composite of recommendations from American Welding Society (AWS) and electrode

manufacturers.

10-2. Safety Information About Tungsten

Ref. S-0161

Grinding the tungsten elec-

trode produces dust and fly-

ing sparks which can cause

injury and start fires. Use lo-

cal exhaust (forced ventila-

tion) at the grinder or wear an

approved respirator. Read

MSDS for safety information.

Consider using tungsten

containing ceria, lanthana,

or yttria instead of thoria.

Grinding dust from thoriated

electrodes contains low-lev-

el radioactive material.

Properly dispose of grinder

dust in an environmentally

safe way. Wear proper face,

hand, and body protection.

Keep flammables away.

Tungsten Electrode With

Balled End

Pointed Tungsten Electrode

Содержание DYNASTY 200 DX





























































































Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды

Miller DYNASTY 200 DX, Руководство пользователя

Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды