Miller DYNASTY 200 DX Скачать руководство пользователя страница 34

Страница: 34 / 92

OM-2240 Page 28

5-10. Sequencer Controls (DX, LX And All CE Models)

Sequencer Control

Sequencing is available only while

using the TIG process, but is dis-

abled if a remote foot or finger cur-

rent control is connected to the Re-

mote receptacle while in the RMT

STD mode. Sequencer parameters

cannot be selected if the Stick pro-

cess (see Section 5-7) is active.
Press switch pad until desired pa-

rameter LED is illuminated.
2

Encoder Control

Ammeter

Turn encoder (see Section 5-2) to

set appropriate value for active se-

quence parameter. Value selected

is shown on the ammeter (see Sec-

tion 5-4). Also, the ammeter LED for

the corresponding unit of measure

(A, S) of the active parameter will be

illuminated.
See Section 5-16 for all Sequencer

parameter ranges.

INITIAL A (

Initial Amperage) - Use

control to select a starting amper-

age that is different from the weld

amperage.

Application:

Initial Amperage can be used while

GTAW welding to assist in preheat-

ing cold material prior to depositing

filler material, or to ensure a soft

start.

INITIAL t (

Initial Time)

(LX Models

Only) -

Press control again and turn

Encoder to select amount of time

that is needed at the beginning of

the weld.

INITIAL SLOPE t

(Initial Slope

Time) Use control to select amount

of time that it takes to slope up/

down from initial amperage to weld

amperage. To disable, set to 0.
4

Amperage Switch Pad

Weld Time

(LX Models Only) -

Press Amperage switch pad twice.

Set desired length of weld time.

FINAL SLOPE t

(Final Slope Time)

- Use control to select amount of

time that it takes to slope up/down

from weld amperage to final amper-

age. To disable, set to 0.

Application:

Final Slope should be used while

GTAW welding materials that are

crack sensitive, and/or the operator

wants to eliminate the crater at the

end of the weld.

FINAL A

(Final Amperage) - Use

control to select amperage to which

weld amperage has sloped up/

down to.

FINAL t

(Final Time)

(LX Models

Only)

- Press control again and turn

Encoder to select amount of time

that is needed at the end of the

weld.

Содержание DYNASTY 200 DX





























































































Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды

Miller DYNASTY 200 DX, Руководство пользователя

Результаты поиска

Содержание DYNASTY 200 DX

Отзывы:

Похожие инструкции для DYNASTY 200 DX

Бренды по названию

Популярные бренды