manualshive.com logo in svg

Miller Auto-Continuum 350, Руководство пользователя

Поделиться
Скачать
Miller Auto-Continuum 350 Скачать руководство пользователя страница 45

OM-273473 Page 41

8-3.

Setup Screen

1

Information Bar

Displays general information on welding pow-
er source, location, asset number, serial num-
ber, and display language.
2

Purge Time

Displays the length of time gas will flow when
the purge button is pressed. Edit button allows
time length to be changed.
3

Enabled Errors

Displays which system errors are enabled.
Click Edit to enable or disable system errors.
4

Jog Speed

Displays the minimum and maximum Jog
speeds in inches per minute (IPM). Edit button
allows minimum and maximum jog speed set-
ting to be changed for forward and reverse jog.
5

Ethernet Settings

Edit button allows user to change connectivity
settings.

6

Data Connections

Displays which data connections are enabled
or disabled.

7

Region

Displays current region. Edit button allows re-
gion to be changed.

8

Status

Displays the status of Insight software. Edit
button allows that status to be changed.

9

WiFi Settings

Edit button allows user to change WiFi 
Settings.

10 Auto Thread

Displays the Load Rate in inches per minute
(IPM) and Torch Length (Inches) to determine
the length of time for Auto Threading. Edit but-
ton allows these parameters to be changed.

11 Wire Spool

Displays wire type, spool size, and amount of
wire remaining on the spool. Edit button allows
wire information to be changed or reset.

12 Weld Cable Setup

Displays length and diameter of positive and
negative weld leads, torch, and voltage feed-
back (VFB) method that are selected. Edit but-
ton allows these parameters to be changed.

13 Robot Options

Displays current robot connectivity options.
Edit button allows robot options to be
changed.

14 Dry Run

15 Relay I/O

1

2

5

3

4

7

6

8

12

10

11

13

14

15

9

Содержание Auto-Continuum 350













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды