Miller 059015051, Руководство пользователя

Страница: 15 / 60

OM-287348 Page 9
SECTION 3 − SPECIFICATIONS
3-1. Serial Number And Rating Label Location
The serial number and rating information for this product is located on the back. Use rating label to determine input power requirements and/or rated
output. For future reference, write serial number in space provided on back cover of this manual.
3-2. Software Licensing Agreement
The End User License Agreement and any third-party notices and terms and conditions pertaining to third-party software can be found at
https://www.millerwelds.com/eula and are incorporated by reference herein.
3-3. Information About Default Weld Parameters And Settings
NOTICE − Each welding application is unique. Although certain Miller Electric products are designed to determine and default to certain typical welding
parameters and settings based upon specific and relatively limited application variables input by the end user, such default settings are for reference
purposes only; and final weld results can be affected by other variables and application-specific circumstances. The appropriateness of all parameters
and settings should be evaluated and modified by the end user as necessary based upon application-specific requirements. The end user is solely
responsible for selection and coordination of appropriate equipment, adoption or adjustment of default weld parameters and settings, and ultimate
quality and durability of all resultant welds. Miller Electric expressly disclaims any and all implied warranties including any implied warranty of fitness
for a particular purpose.
3-4. Specifications
Do not use information in unit specifications table to determine electrical service requirements. See Sections 4-6 and 4-7 for information on con-
necting input power.
This equipment will deliver rated output at an ambient air temperature up to 104 5 F ( 40 5 C).
Model
Rated Output
Max. Open
Circuit
Voltage
Amperage
Range
DC
Dimension
in (mm)
Weight
lb (kg)
100% 60%
35%
(300iP@40%)
260i
400 VAC
50/60 Hz
180 A
23.0 V
210 A
24.5 V
260 A
27.0 V
70.0 V 15-260 A
18.5 x 33 x 42
(1070 x 470 x 830)
125 (57) Net
143 (65) Net
300i P
400 VAC
50/60 Hz
200 A
24.0 V
250 A
26.5 V
300 A
29.0 V
70.0 V 15-300 A
18.5 x 33 x 42
(1070 x 470 x 830)
125 (57) Net
143 (65) Net
320i
400 VAC
50/60 Hz
200 A
24.0 V
250 A
26.5 V
320 A
30.0 V
70.0 V 15-320 A
18.5 x 33 x 42
(1070 x 470 x 830)
125 (57) Net
143 (65) Net
Wire feed speed range: 1.4 mpm to 20 mpm.
3-5. Environmental Specifications
A. IP Rating
IP Rating
IP23S
This equipment is designed for outdoor use. It may be stored, but is not intended to be used outside during precipitation unless sheltered.
IP23S 2014 − 06
B. Temperature Specifications
Operating Temperature Range* Storage/Transportation Temperature Range
− 10 to 40
°
C (14 to 104
°
F)
*Output is derated at temperatures above 40 ° C (104 ° F).
− 20 to 55 ° C ( − 4 to 131 ° F)
Temp_2016- 07
C. Information On Electromagnetic Compatibility (EMC)
!
This Class A equipment is not intended for use in residential locations where the electrical power is provided by the public low
voltage supply system. There can be potential difficulties in ensuring electromagnetic compatibility in those locations, due to con-
ducted as well as radiated disturbances.
This equipment does not comply with IEC 61000 − 3 − 12. If it is connected to a public low voltage system, it is the responsibility of the installer
or user of the equipment to ensure, by consultation with the distribution network operator if necessary, that the equipment can be connected.
IEC/TS 61000-3-4 can be used to guide parties concerned by the installation of arc welding equipment with an input current greater than 16 A
in a low voltage network.
ce-emc 2 2014-07