background image

Talisman III Dynamic Loop Amplifier Systems (TAL/DLS1/3 & TAL/DLS5/3)

Publication Code TAL-DLS-3_TIG Issue 3

Page 12

IN CASE OF SERVICE REQUIREMENTS PLEASE CONTACT YOUR SUPPLIER

IN THE EVENT OF DIFFICULTY COMMUNICATE DIRECT TO:

FEDERAL SIGNAL LIMITED

MILLBANK ELECTRONICS Customer Service

Signal House, Charter Way, Hurdsfield Industrial Estate, Macclesfield, Cheshire SK10 2NF

Telephone: + 44 (0) 1625 666600   -   Fax: +44 (0) 1625 611352  -  Web-site: www.fedsig.co.uk

E-mail: [email protected]    or    [email protected]

7.

Service and Warranty

Federal Signal Ltd. guarantees this product against defects in either

materials or workmanship. The guarantee does not extend to damage
caused by improper installation, improper storage, misuse, or operation
outside stipulated conditions.

Our warranty covers only goods returned to our premises for either repair or
replacement as deemed appropriate by Federal Signal Ltd.
In order to expedite the process:

Contact your supplier and quote the model and serial number of your
equipment.

Should you require sending the goods directly to the manufacturer, please
contact Federal Signal Limited Customer Services, which will provide you
with a Return Goods Authorisation (RGA) number.
This RGA number should then be referenced on every related
correspondence.

If it is necessary to re-pack the equipment for onward shipping or returning
to Millbank for service or repair, PLEASE ENSURE THAT THE ORIGINAL
PACKING OR EQUIVALENT IS USED.

Содержание Talisman TAL/DLS1/3














Отзывы: