manualshive.com logo in svg

Mikrotron EoSens 25CXP, Справочное руководство, Страница: 19 / 70

Поделиться
Скачать
Mikrotron EoSens 25CXP Скачать руководство пользователя страница 19

Connecting an External Power Supply 

 

4CXP Camera 

 

 

MIKROTRON GmbH 

page 19 of 70 

6 Pin Hirose and I/O Signals 

The power connector of the cameras MC4082/MC4083 has to be connected via the 6-pin Hirose 
connector (HR10A-7P-6S) with a DC supply voltage between 12 and 24 V at a power consumption of 
7W max. The DC power supply unit is connected to a dedicated connector at the back side of the 
camera.  Please, take attention to the pin wiring of the connector as described below. 

The 6 pin connector provides a strobe signal (STRB

OUT

) which is low during exposure. 

In case you assemble your own cable, pay attention to the pinning described below. 

 

Table 2:

 

Pinning of the 6 pin power connector 

Pin 

Signal 

Pin 

Signal 

 

1 

VCC 
 

6 

GND 

2 

VCC 
 

5 

GND 

3 

STRB

OUT

 

(3.3 V LVTTL 
I/O standard) 

4 

GND

STRB

 

 

 

 

 

 
WARNING

 

The power connector of the camera has to be connected 
with a DC power supply providing 12 to 24 V DC. 
Connecting a lower or higher supply voltage, an AC 
voltage, reversal polarity (+/-) or using wrong pins of the 
power connector may damage the camera and will void 
warranty. 

 

 

 

Содержание EoSens 25CXP







































































Отзывы:

Нет отзывов