Miele WWB 020 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 80

background image

3. Selecting a program

19

Program selection

The washing machine is switched on by
turning the program selector to a wash
program.



Turn the program selector to the
required program.

The estimated wash time is shown on
the time display and the pre-set
temperature and spin speed light up on
the control panel.

Selecting a temperature and spin
speed

The wash program’s pre-set
temperature and spin speed light up
brightly. The choice of temperatures
and spin speeds selectable for the
wash program light up dimly.



Touch the sensor button for the
temperature desired. It will then light
up brightly.



Touch the sensor button for the spin
speed desired. It will then light up
brightly.

«
...
17
18
19
20
21
...
»

Содержание WWB 020

















































































Отзывы:

Нет отзывов

Похожие инструкции для WWB 020

DW60A608 Series

Бренд: Samsung Страницы: 72

Бренд: Samsung Страницы: 90

Бренд: Samsung Страницы: 20

Бренд: Samsung Страницы: 106

Бренд: VALBERG Страницы: 119

Бренд: Fisher & Paykel Страницы: 7

WA422PRHD Series

Бренд: Samsung Страницы: 36

Бренд: NEW POL Страницы: 20

HD 1050 B 1.810-112

Бренд: Kärcher Страницы: 17

Бренд: Arctic Страницы: 56

Бренд: Kärcher Страницы: 48

Spirit topLine 7540i

Бренд: Schulthess Страницы: 60

Бренд: Erbauer Страницы: 20

Бренд: Gaggenau Страницы: 112

Бренд: Daewoo Страницы: 41

Бренд: Leonard Страницы: 60

Бренд: Gorenje Plus Страницы: 200

Бренд: Fagor Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды