Miele WSG 663 Series Скачать руководство пользователя страница 65

Страница: 65 / 108

Problem solving guide

Fault message at the end of a programme

Problem

Cause and remedy



Check dosage

Excessive foam has built up during washing.



With TwinDos, check the dosage amount set.



Reduce the amount set in 10 % increments.



Use less detergent next time and follow the manu-
facturer's instructions on dosage given on the
packaging.



Hygiene info: run a
programme at min.
75 °C or the "Clean
machine" pro-
gramme

When washing, a wash programme using a temperat-
ure above 60 °C has not been run for a long time.



Turn the programme selector to

Further pro-

grammes





Touch the



sensor controls until

Maintenance

appears in the display.



Touch the

sensor control.

The following appears in the display:

Clean machine



Touch the

sensor control.



Run the

Clean machine

programme using Miele ma-

chine cleaner or a universal powder detergent.

This will clean the washing machine and prevent a
build-up of bacteria and odours.



Align the washing
machine

The

Pre-ironing

extra option which runs at the end of

the programme could not be carried out properly.



Check whether the washing machine is aligned
correctly (see “Installation – Levelling the ma-
chine”).



Check whether the maximum drain height of 1 m
has been exceeded.

If the fault message appears again, contact the Miele
Customer Service Department. The washing machine
can still be used, but without the

Pre-ironing

extra op-

tion.

The messages will appear at the end of the programme and when the washing
machine is switched on and need to be confirmed with the

sensor control.

Содержание WSG 663 Series













































































































Результаты поиска

Содержание WSG 663 Series

Отзывы:

Похожие инструкции для WSG 663 Series

Бренды по названию

Популярные бренды

Miele WSG 663 Series, Руководство по эксплуатации

Результаты поиска

Содержание WSG 663 Series

Отзывы:

Похожие инструкции для WSG 663 Series

Бренды по названию

Популярные бренды