WD
A 200, WD
A 210
en - A
U
, NZ
M.-Nr
. 09 807 520/01
Before the first use
Operating the washing machine
OPERA
TING THE W
ASHING MA
CHINE
Washing
W
ASHING
Changing the programme sequence
CHANGING THE PROGRAMME SEQUENCE
Programme chart
6
7
1
2
3
4
5
8 9
寮
Before using the machine for the first
time, ensure that it is correctly installed
and connected. Please read the separate
operating instructions supplied with the
appliance..
For safety reasons, spinning is not possible
until the machine has been prepared for use
for the first time. To activate the spinning
function, you must run a wash programme
without laundry and without detergent.
Using detergent could result in an exces-
sive build-up of foam.
This also activates the ball valve. The ball
valve prevents detergent escaping from the
suds container into the sump during a wash
programme, thus making maximum use of
the detergent.
Running the first programme
ĺ
Turn on the tap.
ĺ
Switch on the washing machine with the
button.
ĺ
Turn the programme selector to
Cottons
60°C
.
ĺ
Press the
Start/Stop
button.
ĺ
Switch the washing machine off at the
end of the programme.
The machine is now ready for use.
1
Display
The display shows the programme dura-
tion (Time left display), the programma-
ble functions and the Delay start time.
2
Start
button
For starting the wash programme and
selecting Delay start.
3
Extra option buttons
For selecting Extra options. Use the
upper button to select Short, Pre-wash
or Soak. Use the lower button to select
Water plus.
Indicator light on = option selected
Indicator light off = option not selected
4
Spin
button
With spin speed indicator lights for
selecting the spin speed.
5
Programme selector
For selecting a wash programme.
6
Programme sequence indicator
lights
Show which stage of the programme
has been reached.
7
Check / Fault indicator lights
See "Problem solving guide". The PC
check light is also used by service tech-
nicians to run diagnostic checks and
may be used to update programming
data in the future.
8
button
For switching the washing machine
on and off. To save energy, the wash-
ing machine will switch off automati-
cally 15 minutes after the end of the pro-
gramme / Anti-crease phase or after
being switched on if no other selection
is made.
9
Door
button
For opening the door.
Programme duration
After the programme has started, the pro-
gramme duration will appear in the display
in hours and minutes.
When Delay start is being used, the pro-
gramme duration will appear after the Delay
start time has elapsed.
Delay start
The Delay start time selected will appear
in the display. After the programme has
started, the Delay start time will begin to
count down. Once the Delay start time has
finished, the programme begins and the
estimated programme duration appears in
the display.
Programmable functions
The programmable functions can be used
to tailor washing programmes to suit your
personal requirements. In programming
mode, the display will show the function
selected.
Washing environmentally and economically
–
To make the most out of your machine,
load the maximum dry load for the pro-
gramme you are using.
–
When smaller amounts of laundry are
washed, the automatic load recognition
system will reduce the amount of water
and energy used.
–
Use the
Express 20
programme for
small, lightly soiled loads.
–
Modern detergents enable washing at
reduced temperatures (e.g. 20°C). Use
appropriate temperature settings for
saving energy.
–
Reduce the amount of detergent with
smaller loads (approx. 1/3 less than the
amount recommended can be used
when washing a half load).
–
Selecting the highest possible spin
speed for the wash programme will
save energy when drying in a tumble
dryer afterwards.
1. Preparing the laundry
ĺ
Empty all pockets.
寮
Foreign objects (e.g. nails,
coins, paper clips, etc.) can
cause damage to garments and
components in the machine.
ĺ
Sort the laundry by colour and by care label. Most gar-
ments have a textile care label in the collar or side seam.
ĺ
Pre-treat stains and badly soiled areas (see the booklet
"Miele's guide to laundry care").
2. Selecting a programme
ĺ
Switch on the washing machine with the
button.
Switching on Delay Start (if required)
Make sure the programme selector is at the
Finish
position.
ĺ
Press the
Start
button repeatedly to select the delay
time you want.
Programme selection
ĺ
Turn the programme selector to the required pro-
gramme.
The estimated programme duration will appear in the dis-
play.
During the first 10 minutes the machine measures how
much water is being absorbed by the laundry. The pro-
gramme duration may be longer or shorter depending
on this absorbency rate.
1
2
3
1
Detergent dispenser drawer
2
Control panel
3
Door
3. Loading the washing machine
Opening the door
ĺ
Press the
Door
button to open the door.
ĺ
Unfold the laundry and load loosely in the drum.
Mixing both large and small items gives better wash
results and also helps distribute the load evenly during
spinning.
Closing the door
Make sure that no items are
caught between the door and
the seal.
ĺ
Shut the door with a gentle swing.
4. Selecting programme settings
Selecting Extras
Each press of the upper button selects the Extra options:
Soak
or
Pre-wash
or
Short
or no Extra option.
Use the lower button to select the
Water plus
Extra option.
ĺ
Select the Extra option(s) you want.
Useful tip:
Not all the Extra options can be used with
every programme.
You can only select Extra options which are compatible
with the programme being used.
Selecting a spin speed
You can alter the preset spin speed of a wash pro-
gramme.
ĺ
Press the Spin button repeatedly until the indicator light
of the spin speed you want comes on.
5. Adding detergent
ĺ
Pull out the
detergent drawer
and add
detergent to the
compartments.
Detergent for the pre-wash (divide the
total recommended amount as fol-
lows: add 1/3 to compartment
und
2/3 to compartment
)
Detergent for the main wash, includ-
ing Soak if selected
Fabric softener or liquid starch
ĺ
Close the detergent dispenser drawer.
See "Detergent" in the operating instruc-
tions for more information.
6. Starting the programme - the
end of the programme
Starting the programme
ĺ
Press the flashing
Start
button.
At the end of the programme
When the programme has finished, the
Anti-crease/Finish
indicator light will light up
in the programme sequence display and
will appear in the display.
The washing machine will switch off auto-
matically 15 minutes after the end of the
Anti-crease phase. Press the
button to
switch it back on again.
ĺ
Press the
Door
button to open the door.
ĺ
Remove the laundry.
寮
Check that all items have been
removed from the drum.
ĺ
Check the folds
in the door seal
for any small
articles, e.g.
buttons, which
might be lodged
there.
ĺ
Switch the washing machine off with the
button.
ĺ
Turn the programme selector to
Finish
.
ĺ
Close the door.
Cancelling a programme
ĺ
Turn the programme selector to
Finish
.
The suds will be pumped away. The water
will drain away. The programme is cancelled
as soon as the Anti-crease/Finish indica-
tor light comes on and
appears in the dis-
play.
Removing the laundry
ĺ
Turn the programme selector to Drain/
Spin.
Useful tip:
Please take note of the spin
speed selected.
ĺ
Press the Start button.
ĺ
Press the Door button.
ĺ
Remove the laundry.
Selecting another programme
ĺ
Switch the washing machine off and then
back on with the
button.
ĺ
Check that there is still detergent in the
dispenser drawer. Add more detergent if
necessary.
ĺ
Turn the programme selector to the pro-
gramme you want and start the pro-
gramme by pressing the Start button.
Making changes
Programme
Once a programme has started, it is no
longer possible to select a different pro-
gramme.
Temperature
The temperature can be changed within six
minutes of the programme starting.
Spin speed
The spin speed can be changed at any
time.
Extras
It is possible to select or deselect the Water
plus Extra option up to six minutes after the
programme has started.
Interrupting a programme
ĺ
Switch the washing machine off with the
button.
ĺ
Switch the washing machine back on
with the
button to continue with the
same programme.
Adding or removing laundry
after a programme has started
ĺ
Press the
Door
button until the door
opens.
ĺ
Add or remove items.
ĺ
Close the door.
The programme will continue.
Once a programme has started, the
washing machine cannot recognise any
adjustment to the load.
For this reason, if laundry is added or
removed after the start of a programme,
the machine will always complete the pro-
gramme cycle assuming a full load.
This can lead to an increase in the time
left displayed.
The door cannot be opened if:
–
the suds temperature is above 55°C.
–
the water is above a certain level.
–
the programme has reached the
Spin
stage.
P
rogr
amme
Load
(in kg)
Temper
atur
e
Items
Extr
a options
Cott
ons
7.0
30°C t
o 90°C
Cott
ons, linens or cott
on mix fabrics, e.g. table linen, t
owelling,
under
wear
, T
-shir
ts etc.
, , ,
Minimum ir
on
3.5
20°C t
o 60°C
S
ynthetic, mix
ed fibr
e and easy car
e cott
on.
, , ,
Aut
omatic plus
5.0
40°C
Mix
ed loads of garments suitable for the Cott
ons and Minimum
iron pr
ogr
ammes. Sor
t accor
ding t
o colour
.
Dark garments/
Denim
3.5
40°C
Black and dark garments made fr
om cott
on, mix
ed fibr
es and
denim.
, ,
Expr
ess 20
3.5
40°C
Cott
on garments that have har
dly been worn or ar
e only ver
y
lightly soiled.
,
Shir
ts
2.0
40°C
Shir
ts and blouses made of cott
on and mix
ed fibr
e.
, , ,
W
oollens
2.0
Cold and 30°C
Machine-washable or hand-washable wool or wool blend fabric. If the car
e label does not specify a t
emper
atur
e, wash using the
cold setting.
Delicat
es
2.0
Cold t
o 40°C
Delicat
e garments made fr
om synthetic fibr
e, mix
ed fibr
e, r
ayon
and viscose. Cur
tains, including net cur
tains, specified as machine-washable
by the manufactur
er
.
, ,
Dr
ain/Spin
–
–
Dr
ain only: Select
for the spin speed.
Separ
at
e rinse/
S
tar
ch
7.0
For rinsing hand-washed it
ems.
S
tar
ching table cloths, ser
viett
es and workwear
.
= Shor
t;
= P
re-wash;
= Soak;
= W
at
er plus
