background image

Caring for the environment

6

Disposal of the transport
packaging material

The packaging material protects the
dryer from transport damage. The
packaging materials used are selected
from materials which are
environmentally friendly for disposal
and should be recycled.

Recycling the packaging reduces the
use of raw materials in the
manufacturing process and also the
amount of waste.

Disposal of your old appliance

Electronic and electrical appliances
contain many valuable materials. They
also contain certain materials,
compounds and components which
were essential for the proper
functioning and safe use of the
equipment. These could be hazardous
to your health and to the environment if
disposed of with general waste or if
handled incorrectly. Therefore, please
do not dispose of your old appliance
with general waste.

Consult with local authorities, dealers or
Miele in order to dispose of and recycle
electrical and electronic appliances.
Miele assumes no responsibility for
deleting any personal data left on the
appliance being disposed. Please
ensure that your old appliance is kept
away from children until removal.
Observe safety requirements for
appliances that may tip over or pose an
entrapment hazard.

Содержание TXR 860 WP





































































































Отзывы: