Miele TDA 140 C Скачать руководство пользователя страница 18

Страница: 18 / 60

Changing the programme sequence

Once a programme has started

... changing the programme once it

has started

You cannot change to another

programme once a programme has

started (this prevents unintentional

alterations).
If you try to change a programme,



lights up until the original programme is

reset.
You will need to cancel the current

programme before you can select a

new one.

... cancelling a programme



Turn the programme selector to

Finish

The items will be cooled down,

depending on the temperature reached

and how long they have been dried for.
The programme is not finished until



lights up.



Switch the dryer off and then on

again.



Select and start a new programme

immediately.

Adding or removing laundry

after a programme has started



Restart the programme

immediately

after adding or

removing items.

Otherwise remove all items and

spread them out to cool down

completely.

Danger of burning.
The drum and the items can get very

hot.
Do not touch the back of the drum

when adding or removing items.



Press the

Door

button.



Add or remove items.



Close the door.



Press the

Start

button.

Programme duration

Altering the programme sequence can

cause adjustments in the

h min

display.

Содержание TDA 140 C





























































Результаты поиска

Содержание TDA 140 C

Отзывы:

Похожие инструкции для TDA 140 C

Бренды по названию

Популярные бренды

Miele TDA 140 C, Руководство по эксплуатации

Результаты поиска

Содержание TDA 140 C

Отзывы:

Похожие инструкции для TDA 140 C

Бренды по названию

Популярные бренды