Miele HG07-W страница 97 Скачать руководство пользователя

Страница: 97 / 124

Problem solving guide

Fault messages

Issue

Cause and remedy

The warning buzzer is
sounding.
One of the following
faults appears in the
display:

Before rectifying the problem:



Switch the dishwasher off.



Fault FXX

There may be a technical fault.



Switch the dishwasher back on after a few
seconds.



Restart the desired programme.

If the fault message appears again, there is a
technical fault.



Switch the dishwasher off.



Close the stopcock.



Call Miele Service.



Waterproof

The Waterproof system has reacted.



Switch the dishwasher off.



Close the stopcock.



Call your Miele dealer.



Fault F78

Circulation pump fault.



Switch the dishwasher off.



Switch the dishwasher back on.



Restart the desired programme.

If the fault message appears again, there is a
technical fault.



Switch the dishwasher off.



Close the stopcock.



Call your Miele dealer.

Содержание HG07-W





























































































































Результаты поиска

Содержание HG07-W

Отзывы:

Похожие инструкции для HG07-W

Бренды по названию

Популярные бренды

Miele HG07-W, Руководство по эксплуатации

Результаты поиска

Содержание HG07-W

Отзывы:

Похожие инструкции для HG07-W

Бренды по названию

Популярные бренды