Miele HG07-W страница 46 Скачать руководство пользователя

Страница: 46 / 124

Settings

Heat accumulator

This dishwasher is equipped with a heat
accumulator (see “Caring for the
environment – Heat accumulator”).

Select State

The heat accumulator function can be
switched off if you do not wish to use it.
This will increase energy consumption.



Select the

State

menu option.



Select the setting you want and
confirm with

Empty manually

You can manually empty the heat
accumulator, e.g. for a longer period of
absence, or before moving the
appliance to a new location.



In doing so, please ensure that the
dishwasher is properly connected.



Select the

Empty manually

option.

The process starts straight away.

Software version

You can call up the electronic software
version of your dishwasher for technical
support purposes.

Showroom

For demonstration purposes only.

The dishwasher is equipped with a
demo mode for showroom use.

Factory default

You can reset all dishwasher settings to
the factory default settings.

WiFi module settings (where applicable)
have to be reset separately (see
“Settings – Miele@home”).



Select

Reset

and confirm with

Содержание HG07-W





























































































































Результаты поиска

Содержание HG07-W

Отзывы:

Похожие инструкции для HG07-W

Бренды по названию

Популярные бренды

Miele HG07-W, Руководство по эксплуатации

Результаты поиска

Содержание HG07-W

Отзывы:

Похожие инструкции для HG07-W

Бренды по названию

Популярные бренды