Miele HG07-W Скачать руководство пользователя

Страница: 20 / 124

Guide to the appliance

Display functions

The display is used to select or set the
following:

- The programme

- The timer

- The

Settings 

The display can show the following:

- The stage the programme is at

- The estimated time left for the

programme to run

- The energy and water consumption

(EcoFeedback)

- Any relevant fault messages and

information

To save energy, the dishwasher
switches off after a few minutes if you
do not press any sensor controls
during this time.
Touch the



sensor control to switch

the dishwasher back on.

The

sensor control is used to

confirm a message or setting and also
to move to the next menu or another
level.

Under



Further programmes/settings

the right of the display will show a scroll
bar



. This offers further options. These

options can be shown using the



sensor controls.

You can alter the dishwasher’s controls
to suit changing requirements in the
Settings menu (see “Settings” chapter).

The option that is selected will have a
tick



next to it.

To exit a sub-menu again use the



Back

sensor control.

If you do not press any sensor controls
for several seconds, the display will
revert to the previous menu. You may
then have to enter your settings again.

Содержание HG07-W





























































































































Результаты поиска

Содержание HG07-W

Отзывы:

Похожие инструкции для HG07-W

Бренды по названию

Популярные бренды

Miele HG07-W, Руководство по эксплуатации

Результаты поиска

Содержание HG07-W

Отзывы:

Похожие инструкции для HG07-W

Бренды по названию

Популярные бренды