Miele G 1 Series страница 49 Скачать руководство пользователя

Страница: 49 / 76

The dishwasher does not fill/drain

Problem

Possible cause

Remedy

The buzzer sounds.
The Inlet/Drain check
indicator flashes.

The tap is closed.

Open the tap fully.

The buzzer sounds.
The dishwasher stops
during a programme.
The Inlet/Drain check
indicator flashes.
Fault code FXX shows
in the display.

Before rectifying the problem
you must:

– Switch the dishwasher off with

the On/Off button

Fault F12/F13:
Water intake is
restricted.

– Open the tap fully.

– Clean the water inlet filter (see

Maintenance).

– The water pressure at the

intake is lower than 30 kPa
(0.3 bar).
Seek professional advice.

Fault F11:
Water outlet is
restricted, water
remains in the wash
cabinet at the end of
a programme.

– Clean the filter combination.

See Cleaning and care.

– Clean the drain pump. See

Maintenance.

– Clean the non-return valve.

See Maintenance.

– Remove any kink in the drain

hose.

Problem solving guide

Содержание G 1 Series













































































Результаты поиска

Содержание G 1 Series

Отзывы:

Похожие инструкции для G 1 Series

Бренды по названию

Популярные бренды

Miele G 1 Series, Руководство по эксплуатации

Результаты поиска

Содержание G 1 Series

Отзывы:

Похожие инструкции для G 1 Series

Бренды по названию

Популярные бренды