Miele EVS 7010 Скачать руководство пользователя страница 28

Страница: 28 / 64

Operation

After the vacuum-sealing process

A signal sounds.



Open the glass lid.



Danger of burning due to hot

surfaces.
The sealing bar and weld seam are
hot.
Do not touch the sealing bar or the
weld seam immediately after the vac-
uum-sealing process.



Remove the vacuum-sealing bag
from the vacuum chamber.

Before starting a new vacuum-seal-
ing process, check that the vacuum
chamber and the sealing bar are
clean and dry.
Remove any soiling or liquid residues
if necessary.

Sealing the bag early

You can end the vacuum-sealing
process before reaching the selected
vacuum setting and seal the bag early.



Touch the

Seal

sensor control.

The vacuum-sealing process stops. Af-
ter a few seconds the bag will be
sealed.

Successful sealing of the bag is only
possible when there is a minimum
vacuum (vacuum setting 1) in the
chamber.
Touch the

Seal

sensor control again if

the required vacuum setting has not
yet been reached. For technical rea-
sons, a few seconds will elapse before
the bag is sealed.

Содержание EVS 7010

































































Результаты поиска

Содержание EVS 7010

Отзывы:

Бренды по названию

Популярные бренды

Miele EVS 7010, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание EVS 7010

Отзывы:

Бренды по названию

Популярные бренды