manualshive.com logo in svg

Miele EVS 7010, Инструкции по эксплуатации и монтажу

Поделиться
Скачать
Miele EVS 7010 Скачать руководство пользователя страница 20

Operation

20

Storage compartment
(EVS 7670 only)

Risk of damage due to overload-

ing.
Overloading the storage compart-
ment will damage the telescopic run-
ners.
Only load the storage compartment
with maximum 

33 lb (15 kg)

.

Opening the storage compartment

Open the drawer.

Place a thumb in front of one of the
protrusions on the side of the vac-
uum-sealing compartment. Place
your remaining fingers on the side of
the vacuum-sealing compartment.

If the surface of the vacuum-sealing
compartment is hard to grip (e.g., due
to cooking fumes), use both hands to
open the vacuum-sealing compart-
ment.

Slide the vacuum-sealing compart-
ment back until approximately half of
the storage compartment is visible.

Reach behind the recess in the front
of the vacuum-sealing compartment
from below and push the vacuum-
sealing compartment back com-
pletely.

Closing the storage compartment

Close the drawer.

Reopening the vacuum-sealing com-
partment

Follow the instructions for opening
the storage compartment in reverse
order.

Содержание EVS 7010

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды