Midimuso MDCO-3 Скачать руководство пользователя страница 1

Midimuso MDCO-3

Overview:

The 

Midimuso MDCO-3

 is a 

MIDI

-controlled, 

2

 voice 

oscillator

 IC with 

Volts / Hz

 high-resolution control voltage outputs.

Two

 independent square-wave oscillators per chip.

Two

 separate trigger outputs for envelope generators / gates.

(5V for “note on” or 0V for “note off”)

Chainable

: More 

MDCO-3

s can be linked to produce more polyphony

(up to 

12

 mono voices, 

unlimited

 Poly / Unison voices *)

Volts / Hz

 high resolution control voltage outputs using 

“8 + 8” Fast Hybrid PWM

which can be used to provide the correct 

charging voltage

 for an 

integrator

 circuit 

to produce 

sawtooth

 or 

triangle

 waves or used to 

retro-fit

 systems which use the 

Volts / Hz

 pitch system.

Pitch range

 of 

8 octaves

 (MIDI keys C0 to C8) i.e. 32.5 Hz to 8.4 kHz

Pitch accuracy

 of 

0.0006%

 of one semitone at Middle C

Pitch Bend

 (range can be set by user)

Guaranteed

 pitch stability (quartz controlled)

Pulse-Width

 control and D

etune

 on every oscillator

Polyphonic

Unison

 and 

Monophonic

 modes

Velocity

 and MIDI-

Volume

 outputs available in Unison mode

9

 auxilliary 

triggers

 per chip for general use (5V for “note on” or 0V for “note off”

for drum machines etc.).
These can be chained so that 2 chips give 18 triggers
to a 

max

 of 4 chips giving 36 triggers.

MIDI Clock

 out in all modes

Built-in Test Mode

 to allow you to accurately calibrate conversion-precision

using just an audio amplifier.

PANIC MODE! 

Sending Program Change 9 resets main parameters

* Delay from chip to chip is less than 1 millisecond.

Содержание MDCO-3










Отзывы: