MICROTRONIX DX-4400 Series Скачать руководство пользователя страница 16

Страница: 16 / 125

DX-4400

– 3G-SDI Text & Graphics Overlay Inserter – User Manual

Page 16 of 125

3 Operation

3.1

Powering on the DX-4400

The  DX-4400  unit  operates  from  at  12VDC  from  the  supplied  120/240VAC  power  adapter.    Each  time  the
DX-4400  is  powered  on  it  requires  the  microSD  Card  installed  in  the  card  slot  to  enable  it  to  boot  the  Linux
Operating  System  contained  on  the  card.    The  unit  is  shipped  from  the  factory  with  the  micro  SD  Card  pre-
installed in the card slot.

Warning:

If it is necessary to install a microSD Card into the unit, be careful when sliding the card into the card

slot so as to not misalign the card to the card slot connector. Otherwise, the card may accidently fall
inside the unit and will require the chassis to be opened to retrieve the card.

3.2

Modes of Operation

The DX-4400 product has several selectable Modes of Operation. Each mode has different capabilities and
features. The available modes are:

Dual Text Inserter (Dual TI)

. In this mode the product provides two video channels with separate text

and graphics overlays for each channel. Each channel supports the SD, HD, and 3G modes listed in the

product specifications with ancillary data pass through.

Low Latency Dual Text Inserter (LDual TI)

. In this mode the product provides two video channels with

separate text and graphics overlays for each channel without frame buffers in the path. Each channel

supports the SD, HD, and 3G modes listed in the product specifications with ancillary data pass-through.

There is no SDI alpha blending.

Zoom Dual Text Inserter (ZDual TI)

. In this mode the product provides two video channels with separate

text and graphics overlays for each channel. Each channel supports the SD, HD, and 3G progressive

modes (no interlaced or PsF modes) listed in the product specifications without ancillary data pass-

through. Each channel supports separate zoom control.

Picture in Picture Text Inserter (PiP TI)

. This mode provides a single text inserter with a main input and

a secondary input. Both inputs have scaling capabilities to allow for use as Picture in Picture (PiP), split

screen or side by side configurations. The unit has a single text and graphics overlay and supports the

SD, HD, and 3G modes listed in the product specifications. Ancillary data from input 1 passes through the

unit to the output.

Low Latency Picture in Picture Text Inserter (LPiP TI)

. This mode provides a single text inserter with

less than one frame of delay from input 1 to the output. Input 1 does not support PiP or Zoom. Input 2

supports PiP and Zoom. Ancillary data is supported on Input 1.

Dual Link 4K Text Inserter (4K TI)

. The unit provides a text and graphics overlay for one channel of 4K

(Quad and 2SI mapped) video transported in the dual link modes listed in the product specifications.

Ancillary data pass through is NOT supported.

Low Latency Dual Link 4K Text Inserter (L4K TI)

. The unit provides a text and graphics overlay for one

channel of 4K (Quad and 2SI mapped) video transported in the dual link modes without frame buffers in

the video path. Ancillary data pass through is supported in this mode of operation.

Zoom 4K Dual Link 4K Text Inserter (Z4K TI)

. The unit provides a text and graphics overlay for one

channel of 4K (Quad or 2SI mapped) video transported in the dual link mode. For 2SI mapped video only,

the input can be zoomed. Ancillary data pass-through is supported in this mode of operation.

NOTE: Support for 4K video is an optional product upgrade and is not available in the base

product configuration.

Содержание DX-4400 Series






























































































































Результаты поиска

Содержание DX-4400 Series

Отзывы:

Похожие инструкции для DX-4400 Series

Бренды по названию

Популярные бренды

MICROTRONIX DX-4400 Series, Руководство пользователя

Результаты поиска

Содержание DX-4400 Series

Отзывы:

Похожие инструкции для DX-4400 Series

Бренды по названию

Популярные бренды