Microtronics myDatalogNANOamr Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 125

Microtronics myDatalogNANOamr Скачать руководство пользователя страница 16

4.5 Overview

Overview myDatalogNANOamr

1 Antenna connector

3 Sensor cable with open ends (channel 1 and

channel 2)

2 Sealed sensor cable (channel 3 and

channel 4)

4 Housing cover

4.6 Intended use

The portable measurement instrument is used to record meter readings. The device can operate
without mains power. The measured and recorded data is stored on a non-volatile memory medium.
This stored data is sent via the mobile network to a central server for further processing. The device
is equipped with an integrated SIM chip for this purpose. The maximum permissible limit values
specified in chapter "Technical data " on page 11 must be observed. The manufacturer shall not be
liable for any operational cases that deviate from these limit values and have not been approved by
the manufacturer in writing.

Note: This device is exclusively intended to be used for the purposes as described above.
Any other use or use beyond what is specified or a modification of the device shall be
deemed to be not for the intended purpose and is not permitted without the express written
consent of the manufacturer. The manufacturer shall not be held liable for any damages that
may result from such unauthorised use or modification. The operator alone bears the
associated risk.

Note: The manufacturer is not liable for data loss of any kind if the device is damaged and
data is not able to be stored correctly.

16

Rev. 01

«
...
14
15
16
17
18
...
»

Содержание myDatalogNANOamr






























































































































Отзывы:

Нет отзывов