Microsemi SmartFusion2 MSS Скачать руководство пользователя страница 691 | Manualshive

Страница: 691 / 829

background image

Reset Controller

UG0331 User Guide Revision 15.0

657

21.2.6.1.3 T_RESET_N

This is also a reset signal to the Cortex-M3 processor. The T_RESET_N is a synchronized signal of
PO_RESET_N on TRACECLK (Trace clock input from the clock controller). It asserts asynchronously
and negates synchronously to TRACECLK.

21.2.6.1.4 M3_SYS_RESET_N

M3_SYS_RESET_N resets the Cortex-M3 processor core and its components, excluding the debug
logic.

This reset is generated based on M3_RESET_ M3_CLK_N and SYSRESET_N.
M3_RESET_M3_CLK_N is a synchronized signal of M3_RESET_N from the FPGA fabric on M3_CLK.
The generation of M3_SYS_RESET_N is shown in the following figure.

Figure 289 •

M3_SYS_RESET_N Generation

In the five Cortex-M3 processor resets, M3_SYS_RESET_N is the only reset signal that can be
controlled.

M3_RESET_N is an active low reset input from the FPGA fabric and resets the Cortex-M3 processors if
set to 0. It is only usable in order to extend the duration of system reset to the Cortex-M3 processor after
the rest of the MSS has been released from reset. This allows to perform a secure hardware based code
shadowing function, thereby minimizing boot time.

21.2.6.1.5 M3_TRST_N

This signal is originates from System Controller and drives the NTRST (debug reset) input of the Cortex-
M3 processor and is used to reset the SWJ-DP sub-block within the Cortex-M3 processor.

21.2.6.2 MDDR Resets

21.2.6.2.1 MDDR_AXI_RESET_N

MDDR_AXI_RESET_N is generated from FPGA fabric reset input (MDDR_DDR_CORE_RESET_N),
SYSRESET_N, and the MDDR soft reset (MDDR_CTLR_SOFTRESET) from SYSREG.

The generation of MDDR_AXI_RESET_N is shown in the following figure.

Figure 290 •

MDDR_AXI_RESET_N Generation

The Reset Controller drives a synchronized reset to AXI logic in the MDDR.

21.2.6.2.2 MDDR_APB_RESET_N

MDDR_APB_RESET_N is generated from FPGA fabric PRESET input (MDDR_APB_S_RESET_N) or
SYSRESET_N, based on the selection of MDDR_CONFIG_LOCAL in SYSREG. The
MDDR_CONFIG_LOCAL bit is in the MDDR configuration register (MDDR_CR as defined in

page 669) of SYSREG.

M3_SYS_RESET_N

M3_RESET_M3_CLK_N

SYSRESET_N

MDDR_AXI_RESET_N

MDDR_DDR_CORE_RESET_N

SYSRESET_N

MDDR_CTRL_SOFTRESET

«
...
689
690
691
692
693
...
»

Содержание SmartFusion2 MSS






























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartFusion2 MSS

Бренд: Gardena Страницы: 100

Бренд: IBM Страницы: 72

Бренд: Baby Trend Страницы: 8

Бренд: Baby Trend Страницы: 19

Бренд: Baby Trend Страницы: 5

Бренд: Baby Trend Страницы: 4

Бренд: Banner Страницы: 15

Бренд: bar Страницы: 2

Бренд: Campbell Страницы: 3

VARIVENT D Series

Бренд: GEA Страницы: 78

Бренд: GEA Страницы: 96

Бренд: GEA Страницы: 66

Бренд: UNI Страницы: 21

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: IDK Страницы: 96

Бренд: KEENZ Страницы: 68

Бренд: YASKAWA Страницы: 121

Бренд: YASKAWA Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды