manualshive.com logo in svg

Microsemi SmartFusion2 MSS, Руководство пользователя

Микросхема SmartFusion2 MSS от Microsemi предлагает широкие возможности для пользователей. Чтобы узнать больше о продукте и его настройках, скачайте бесплатное Руководство по эксплуатации на {сайт}. Это руководство поможет вам максимально использовать потенциал данного устройства.

Поделиться
Скачать
background image

Cortex-M3 Processor (Reference Material)

UG0331 User Guide Revision 15.0

19

code overhead from the ISRs. A Tail-chain optimization also significantly reduces the overhead when 
switching from one ISR to another.

To optimize low-power designs, the NVIC integrates with the sleep modes, that include a deep sleep 
function that enables the entire device to be rapidly powered down while still retaining program state.

3.1

System Level Interface

The Cortex-M3 processor provides multiple interfaces using AMBA

®

 technology to provide high speed, 

low latency memory accesses. It supports unaligned data accesses and implements atomic bit 
manipulation that enables faster peripheral controls, system spinlocks, and thread-safe Boolean data 
handling.

The Cortex-M3 processor has an optional memory protection unit (MPU) that provides fine grain memory 
control, enabling applications to utilize multiple privilege levels, separating and protecting code, data and 
stack on a task-by-task basis. Such requirements are becoming critical in many embedded applications 
such as automotive systems.

3.2

Integrated Configurable Debug

The Cortex-M3 processor implements a complete hardware debug solution. This provides high system 
visibility of the processor and memory through either a traditional JTAG port or a 2-pin Serial Wire Debug 
(SWD) port that is ideal for microcontrollers and other small package devices. The MCU vendor 
determines the debug feature configuration and therefore this can differ across different devices and 
families.

For system trace the processor integrates an Instrumentation Trace Macrocell™ (ITM) alongside data 
watchpoints and a profiling unit. To enable simple and cost-effective profiling of the system events these 
generate, a Serial Wire Viewer (SWV) can export a stream of software-generated messages, data trace, 
and profiling information through a single pin.

The optional Embedded Trace Macrocell (ETM) delivers unrivaled instruction trace capture in an area far 
smaller than traditional trace units, enabling many low cost MCUs to implement full instruction trace for 
the first time.

The optional Flash Patch and Breakpoint Unit (FPB) provides up to eight hardware breakpoint 
comparators that debuggers can use. The comparators in the FPB also provide remap functions of up to 
eight words in the program code in the CODE memory region. This enables applications stored on a non-
erasable, ROM-based microcontroller to be patched if a small programmable memory, for example flash, 
is available in the device. During initialization, the application in ROM detects, from the programmable 
memory, whether a patch is required. If a patch is required, the application programs the FPB to remap a 
number of addresses. When those addresses are accessed, the accesses are redirected to a remap 
table specified in the FPB configuration, which means the program in the non-modifiable ROM can be 
patched.

3.3

Cortex-M3 Processor Features and Benefits Summary

•

Tight integration of system peripherals reduces area and development costs.

•

Thumb instruction set combines high code density with 32-bit performance.

•

Code-patch ability for ROM system updates.

•

Power control optimization of system components.

•

Integrated Sleep modes for low power consumption.

•

Fast code execution permits slower processor clock or increases sleep mode time.

•

Hardware division and fast multiplier.

•

Deterministic, high-performance interrupt handling for time-critical applications.

•

Optional memory protection unit (MPU) for safety-critical applications.

•

Extensive debug and trace capabilities—Serial Wire Debug and Serial Wire Trace reduce the 
number of pins required for debugging, tracing and code profiling.

Содержание SmartFusion2 MSS






























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartFusion2 MSS

VADDIO EVI-D70 Installation And User Manual preview
EVI-D70
Бренд: VADDIO Страницы: 2
Baccara G75-DFC Installation Operation & Maintenance preview
G75-DFC
Бренд: Baccara Страницы: 16
BABYSTYLE OYSTER Instruction Manual preview
OYSTER
Бренд: BABYSTYLE Страницы: 8
BABYSTYLE Hybrid 2 Manual preview
Hybrid 2
Бренд: BABYSTYLE Страницы: 32
Balmar Max Charge MC-624 Installation And Operator'S Manual preview
Max Charge MC-624
Бренд: Balmar Страницы: 8
Balmar MAX CHARGE MC-614 Installation And Operation Manual preview
MAX CHARGE MC-614
Бренд: Balmar Страницы: 20
Farfisa TD6100 Manual preview
TD6100
Бренд: Farfisa Страницы: 20
Racal Instruments 1266 Manual preview
1266
Бренд: Racal Instruments Страницы: 64
Maestra 8080 User Manual preview
8080
Бренд: Maestra Страницы: 22
Omnex R1300 Manual preview
R1300
Бренд: Omnex Страницы: 9
Omegon MiniTrack LX2 Instruction Manual preview
MiniTrack LX2
Бренд: Omegon Страницы: 6
WATERLOO Smart Panel Owner'S Manual preview
Smart Panel
Бренд: WATERLOO Страницы: 8
Vega VEGAMET 141 Operating Instructions Manual preview
VEGAMET 141
Бренд: Vega Страницы: 20
BABYTREND Simply Smart PY75 A Series Instruction Manual preview
Simply Smart PY75 A Series
Бренд: BABYTREND Страницы: 32
Ascon tecnologic Y39 Operating Instructions Manual preview
Y39
Бренд: Ascon tecnologic Страницы: 16
KIOUR FA3F Quick Start Manual preview
FA3F
Бренд: KIOUR Страницы: 3
Topway HMT028ATB-C User Manual preview
HMT028ATB-C
Бренд: Topway Страницы: 14
Wave Home Solutions WV-SCBT Installer Manual preview
WV-SCBT
Бренд: Wave Home Solutions Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды