Microsemi SmartFusion2 MSS Скачать руководство пользователя страница 418 | Manualshive

Страница: 418 / 829

background image

Ethernet MAC

UG0331 User Guide Revision 15.0

384

8.

The software should respond to the RxPktReceived interrupt by reading the packet from its location
in the ring buffer and then setting the Empty Flag in the descriptor to ‘1’ again to mark this segment
of the ring buffer as available for storing further received packets.

9.

If a bus error occurs, the DMA controller terminates the sequence of the receive packet transfers,
sets the Bus Error bit in the DMA_RX_STATUS register, and clears the RxEnable bit in the
DMA_RX_CTRL register. If enabled, an interrupt is generated with the DMA Interrupts register
showing an Rx Bus Error as the source of this interrupt.
Any further transfers require the DMA_RX_DESC register to be updated to record the start position
in the ring buffer that is now required and the RxEnable bit is to be set to ‘1’ again.

11.5

How to Use TSEMAC

TSEMAC can be configured using the Libero SoC design software. Using the MSS Ethernet Configurator
macro, external PHY interface can be selected as shown in the following figure. The external PHY
interface can be MII or GMII or TBI. The MII and GMII interfaces are routed though the FPGA fabric onto
the MSIOs, and the TBI interface is routed though the FPGA fabric on-to the SERDESIOs.

Figure 156 •

External PHY Interface Selection in MSS EMAC Configurator

Using the MSS EMAC configurator, the line speed can be selected. Supported line speeds are:

•

10/100 Mbps for the MII interface

•

10/100/1000 Mbps for the GMII and TBI interfaces

«
...
416
417
418
419
420
...
»

Содержание SmartFusion2 MSS






























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartFusion2 MSS

Бренд: Lawler Страницы: 5

Бренд: fakro Страницы: 16

Бренд: e-BLEACH Страницы: 24

Бренд: Lawler Страницы: 4

Бренд: QTP Страницы: 2

Бренд: Yoshitake Страницы: 4

Бренд: YOKOGAWA Страницы: 20

UTAdvanced UT32A

Бренд: YOKOGAWA Страницы: 3

Бренд: Gardena Страницы: 236

Бренд: Paser Страницы: 2

Бренд: Computer Automation Technology Страницы: 55

Бренд: East Coast Datacom Страницы: 14

Бренд: Grundfos Страницы: 23

Бренд: Sungrow Страницы: 4

Бренд: ICP DAS USA Страницы: 7

Бренд: GCE Страницы: 13

Бренд: Leviton Страницы: 2

Бренд: TECH Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды