manualshive.com logo in svg

Microsemi SmartFusion2 MSS, Руководство пользователя

Микросхема SmartFusion2 MSS от Microsemi предлагает широкие возможности для пользователей. Чтобы узнать больше о продукте и его настройках, скачайте бесплатное Руководство по эксплуатации на {сайт}. Это руководство поможет вам максимально использовать потенциал данного устройства.

Поделиться
Скачать
background image

Universal Serial Bus OTG Controller

UG0331 User Guide Revision 15.0

366

10.3.14.2 LPM_ATTR_REG Bit Definitions

10.3.14.3 LPM_CTRL_REG (Peripheral) Bit Definitions

Table 305 • 

LPM_ATTR_REG (0x40043360)

Bit 
Number

Name

Reset 
Value Function

[15:12]

EndPnt

0

This is the endpoint that is in the token packet of the LPM transaction.

[11:9]

Reserved

N/A

8

RmtWak

0

This bit is the remote wake-up enable bit.
0: Remote wake-up is not enabled.
1: Remote wake-up is enabled
This bit is applied on a temporary basis and is applied only to the current suspend 
state. After the current suspend cycle, the remote wake-up capability that was 
negotiated upon enumeration applies.

[7:4]

HIRD

0

This is the host initiated resume duration. This value is the minimum time the host 
drives resume on the bus. The value in this register corresponds to an actual resume 
time as follows:
Resume Time = 50 µs + HIRD × 75 µs.
This results a range 50 µs to 1200 µs.

[3:0]

LinkState

0

This value is provided by the host to the peripheral to indicate what state the 
peripheral must transition to after the receipt and acceptance of a LPM transaction.
0000: Reserved
0001: Sleep state (L1)
0010: Reserved
0011: Reserved

Table 306 • 

LPM_CTRL_REG (0x40043362)(Peripheral)

Bit 
Number

Name

Reset 
Value Function

[7:5]

Reserved N/A

4

LPMNAK 0

Places all endpoints in a state such that the response to all transactions other than an 
LPM transaction is a NAK. This bit takes effect only after the USB controller has been 
LPM suspended. In this case, the USB controller continues to NAK until this bit has 
been cleared by software.

[3:2]

LPMEN

0

Enables LPM in the USB controller. There are three levels in which LPM can be 
enabled, which determines the response of the USB controller to LPM transactions. 
Following are the three levels:
00: LPM and extended transactions are not supported. In this case, the USB 
controller does not respond to LPM transactions and the transaction timeouts.
01: LPM and extended transactions are not supported. In this case, the USB 
controller does not respond to LPM transactions and the transaction timeouts.
10: LPM is not supported but extended transactions are supported. In this case, the 
USB controller responds to an LPM transaction with a STALL.
11: The USB controller supports LPM extended transactions. In this case, the USB 
controller responds with a NYET or an ACK as determined by the value of LPMXMT 
(bit 0 of this register) and other conditions.

1

LPMRES 0

Initiates resume (remote wake-up). This bit differs from the classic RESUME bit 
(POWER_REG.bit2) in that the RESUME signal timing is controlled by hardware. 
When software writes this bit, resume signaling is asserted for 50 µs. This bit is self 
clearing.

Содержание SmartFusion2 MSS






























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SmartFusion2 MSS

S&C 5800 Series Operating Instructions Manual preview
5800 Series
Бренд: S&C Страницы: 40
S&C 5800 Series Troubleshooting Manual preview
5800 Series
Бренд: S&C Страницы: 34
VAT 168 Series Installation, Operating, & Maintenance Instructions preview
168 Series
Бренд: VAT Страницы: 29
Balboa Instruments Dolphin Manual preview
Dolphin
Бренд: Balboa Instruments Страницы: 19
Febco 860 Series Installation Instructions preview
860 Series
Бренд: Febco Страницы: 4
Cisco Catalyst 3110G Hardware Installation Manual preview
Catalyst 3110G
Бренд: Cisco Страницы: 48
Garmin 340 Pilot'S Manual preview
340
Бренд: Garmin Страницы: 12
UniKey SR3 Installation Manual & User Manual preview
SR3
Бренд: UniKey Страницы: 20
7bit Synapse Instruction Manual preview
Synapse
Бренд: 7bit Страницы: 2
Jafar 5220 Operation And Maintenance Manual preview
5220
Бренд: Jafar Страницы: 15
Mamas & Papas luna Manual preview
luna
Бренд: Mamas & Papas Страницы: 44
Mamas & Papas flare Manual preview
flare
Бренд: Mamas & Papas Страницы: 8
Omegalink 553 Quick Start Operation Manual preview
553
Бренд: Omegalink Страницы: 2
MamaLove rider Quick Start Manual preview
rider
Бренд: MamaLove Страницы: 9
Tylo 2900 5208 Installation Manual And Quick Start Manual preview
2900 5208
Бренд: Tylo Страницы: 51
M-system R5-TS Instruction Manual preview
R5-TS
Бренд: M-system Страницы: 3
weintek MT600iWP Series Installation Instruction preview
MT600iWP Series
Бренд: weintek Страницы: 2
Cypress CY3643 Quick Start Manual preview
CY3643
Бренд: Cypress Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды