Approvals
Declaration of conformity
DECLARATION OF CONFORMITY
Manufacturer
Micropower E.D. Markeng AB, Idavägen 1, 35246 Växjö, Sweden, tel +46 (0) 470-727400
Equipment
Ba!ery charger Sharp 50 and 100 with 24, 36 or 48 VDC nominal output and 3x380-440 VAC
The following direc!ves and standards have
been
applied
:
•
Low voltage direcve
2014/35/EU
•
EN 60 335
-
1
,
EN 60 335-2-29
1
•
EMC direcve
2014/30/EU
EN 61000-6-2, E
N 61000 -6-3
•
•
EU RoHS Direcve
2011/65/EU
CE Marking Direcve
93/68/EEC
Note 1: If charger’s rated output voltage is higher than 36 V it doesn’t fulfil ar"cle 10.101 (“The no load d.c output voltage shall not exceed
42,2V”). In some applica"on is an addi"onal resistor mounted between the secondary posi"ve and protec"ve earth for an improved ESD
protec"on. In these case is not 13.3 and 16.3 fulfilled for the secondary side.
As manufacturer we declare under our sole responsibility that the equipment fulfils essenal
requirements for CE conformity according to applied direcves and standards.
Date
Signature
Posi!on
2016-08-24
Henrik Litsin
R&D Manager
•
nominal input.
Ba!ery charger Sharp 30 with 24, 36 or 48 VDC nominal output and 1x230 VAC nominal input.
246
Содержание Sharp 100
