Micromeritics AccuPyc 2 1340 Скачать руководство пользователя страница 25

Страница: 25 / 158

AccuPyc II 1340

Installing the Analyzer

June 2013

2-7

If connecting a printer:

a. Connect one end of the printer cable to a USB connector. Connect the other end to the

input connector on the printer.

b. Press

Alt

to access the Set-up function

c. Press

CHOICE

until

Report Options

displays on the fourth line of the display (refer

Report Options

, page

3-14

), then press

ENTER

d. Press

ENTER

until the

Print Report?

prompt displays; press

CHOICE

to select

Yes

e. Press

ENTER

until the

Printer?

prompt displays; choose the appropriate printer (refer

SUPPORTED PRINTERS

, page

G-1

for information on supported printers.

f. Press

SAVE

to save your selections and return to the

Reload

prompt.

10. If you have a temperature-controlled AccuPyc, attach the circulating bath (refer to

TEMPERATURE-CONTROLLED ACCUPYC

, page

F-1

) before proceeding with the

next step.

11. Plug the printer power cord and the pycnometer power cord (which is plugged into the

AC/DC power supply) into an appropriate power source.

Содержание AccuPyc 2 1340






























































































































































Результаты поиска

Содержание AccuPyc 2 1340

Отзывы:

Похожие инструкции для AccuPyc 2 1340

Бренды по названию

Популярные бренды

Micromeritics AccuPyc 2 1340, Руководство оператора

Результаты поиска

Содержание AccuPyc 2 1340

Отзывы:

Похожие инструкции для AccuPyc 2 1340

Бренды по названию

Популярные бренды