Micromeritics AccuPyc 2 1340 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 158

background image

AccuPyc II 1340

Equipment Description

Aug 2013

1-7

Large-Volume Core Pycnometer

The AccuPyc Large-Volume pycnometer sample chamber has been designed to address the specific
needs of operations that require pore volume knowledge of intact drilling cores. This instrument elimi-
nates the need to break core samples into smaller pieces prior to being analyzed.

The large-volume core pycnometer:

•

Has a large sample chamber with a volume of approximately 2000 cm

3

.

•

Has a sample chamber can accommodate a 95 mm (3.74 in.) diameter core of up to

278 mm (10.9 in.) in length.

FoamPyc

A

FoamPyc

option for measuring open- and closed-cell foam materials is available in the following

configurations for the standard and temperature-controlled pycnometers:

• 100-cm

3

nominal cell volume (recommended)

• 10-cm

3

nominal cell volume

This unit can be ordered initially with the FoamPyc application installed, or if you have a standard
AccuPyc, you can upgrade with a software enhancement via USB media.

MultiVolume Inserts

A MultiVolume option allowing you to analyze smaller-sized samples with your current AccuPyc
model is available for the following configurations:

• 1-cm

3

nominal cell volume, contains a 0.1 cm

3

cup

• 10-cm

3

nominal cell volume, contains 1- and a 3.5-cm

3

cups

• 100-cm

3

nominal cell volume, contains 10- and 35-cm

3

cups

• 2000-cm

3

nominal cell volume, contains 650- and 1300-cm

3

cups

Each kit includes appropriate insert(s), reference standard(s), and sample cup(s). Instructions for using
multivolume inserts are located in

MULTIVOLUME INSERTS

. Refer to

INFORMATION

for additional information.

Multigas Option

The Multigas Option enables you to connect up to four gases to one analyzer. Installation and opera-
tion instructions are provided in

MULTIGAS OPTION

. Refer to

INFORMATION

for details on placing an order.

«
...
13
14
15
16
17
...
»

Содержание AccuPyc 2 1340































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AccuPyc 2 1340

Бренд: Unico Страницы: 10

Бренд: Qu-Bit Electronix Страницы: 10

Бренд: Energometrika Страницы: 39

Бренд: kruss Страницы: 115

Бренд: Rae Страницы: 38

Бренд: FlowLine Страницы: 2

Бренд: Kipp & Zonen Страницы: 32

Бренд: Bahco Страницы: 21

Бренд: Kübler Страницы: 72

Бренд: Kingfisher Страницы: 52

MultiScanner HD800 OneStep

Бренд: Zircon Страницы: 2

Бренд: HERON Страницы: 2

Бренд: TDI Страницы: 32

Бренд: General Страницы: 12

my mp3 grand piano

Бренд: ItsImagical Страницы: 5

Бренд: ATD Tools Страницы: 2

Бренд: T&D Страницы: 2

Бренд: DAKOTA ULTRASONICS Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды