5
Microlife BP B6 Connect
EN
Support your arm so it is relaxed.
Ensure that the cuff is at the same height as your heart.
4. Taking a blood pressure measurement
Select standard (single measurement) or MAM mode (auto
-
matic triple measurement): see details in chapter 2.«
Press the ON/OFF button
1
to start the measurement.
The cuff will now pump up automatically. Relax, do not move
and do not tense your arm muscles until the measurement
result is displayed. Breathe normally and do not talk.
The cuff fit check
BT
on the display indicates that the cuff is
perfectly placed. If the icon
BT
-A appears, the cuff is fitted
suboptimally, but it is still ok to measure.
When the correct pressure is reached, the pumping stops and the
pressure falls gradually. If the required pressure was not reached,
the device will automatically pump some more air into the cuff.
During the measurement, the pulse indicator
BS
flashes in the
display.
The result, comprising the systolic
AP
and the diastolic
AQ
blood
pressure and the pulse rate
AR
are displayed. Note also the
explanations on further display symbols in this booklet.
When the device has finished measuring, remove the cuff.
Switch off the device. (The monitor does switch off automati
-
cally after approx. 1 min.).
AF detection is only activated in MAM mode.
You can stop the measurement at any time by pressing the
ON/OFF button (e.g. if you feel uneasy or an unpleasant
pressure sensation).
This monitor is specially tested for use in pregnancy and
pre-eclampsia. When you detect unusual high readings in
pregnancy, you should measure after a short while again
(eg. 1 hour). If the reading is still too high, consult your
doctor or gynecologist.
In pregnancy the AFIB symbol can be ignored.
Manual inflation
In case of high systolic blood pressure (e.g. above
135
mmHg),
it can be an advantage to set the pressure individually.
Press the ON/OFF button after the monitor has been pumped up
to a level of approx. 30 mmHg (shown on the display). Keep the
button pressed until the pressure is about 40 mmHg above the
expected systolic value – then release the button.
How not to store a reading
As soon as the reading is displayed press and hold the ON/OFF
button
1
until
«M»
BP
is flashing. Confirm to delete the reading by
pressing the Bluetooth/Time button
4
.
«CL»
is displayed when the reading is deleted from the
memory successfully.
How do I evaluate my blood pressure
The LED traffic light indicator on the left-hand side of the display
8
indicates within which range the measured blood pressure lies.
The value is either within the optimum (green), elevated (yellow) or
high (red) range. The classification corresponds to the following
ranges defined by international guidelines (ESH, ESC, JSH). Data
in mmHg.
The higher value is the one that determines the evaluation.
Example: a blood pressure value of
140/80
mmHg or a value of
130/90
mmHg indicates »blood pressure too high«.
Average Indicator «MyCheck»
This symbol
CT
indicates after each measurement, if the most
recent measured value lies below, above or on the same level as
your stored average value (see also chapter »5. Data memory«).
If the measured Systole or Diastole is more than 5mmHg
higher than the stored average, the arrow shows upwards.
If the measured Systole or Diastole is more than 5mmHg
lower than the stored average, the arrow shows down
-
wards.
If the measured Systole and Diastole do not differ by more
than 5mmHg from the stored average, the arrow shows
straight on.
If the measured systole and diastole differ in different direc
-
tions from the stored average, this is indicated first with the
systole figure flashing, together with the up or down arrow
for two seconds. Thereafter, the diastole figure flashes with
the arrow pointing up or down for two seconds.
Range
Systolic Diastolic Recommendation
1. blood pressure
too high
≥135
≥85
Seek medical
advice
2. blood pressure
elevated
130 - 134 80 - 84
Self-check
3. blood pressure
normal
<130
<80
Self-check
Содержание BPB6 Connect
Страница 130: ...128 ...
