Microhard Systems pMDDL5824 Скачать руководство пользователя страница 71

Страница: 71 / 117

4.0 Configuration

Image 4

1: Serial > Summary

4.5 Serial

4.5.1 Serial > Summary

The Serial > Summary window gives a summary of the on board serial and console data ports.

Gadget

If the pMDDL5824 has been set to USB Device mode (Pin 72 connected to GND through a 1K

resistor), the Gadget tab will appear and the USB port can be used to connect to a USB host that has the

Microhard Composite Drivers installed. The USB port will appear as a serial device on the host system.

The Summary window shows a number of status items that aid in viewing the operation, statistics, and

troubleshooting of the Serial & USB Serial Ports.

General Status

•

Port

Shows if the data port has been configured for Console, Data or Idle

•

Port Status

Shows if the data port has been enabled in the configuration.

•

Baud Rate

The current baud rate used to interface with the connected device.

•

Connect As

The type of IP Protocol Config is displayed here (TCP, UDP, SMTP, PPP, etc)

•

Connect Status

Shows if there are any current connections / if the port is active.

Содержание pMDDL5824






















































































































Результаты поиска

Содержание pMDDL5824

Отзывы:

Похожие инструкции для pMDDL5824

Бренды по названию

Популярные бренды

Microhard Systems pMDDL5824, Руководство по эксплуатации

Результаты поиска

Содержание pMDDL5824

Отзывы:

Похожие инструкции для pMDDL5824

Бренды по названию

Популярные бренды