microHAM Digi Keyer II Скачать руководство пользователя страница 7

Страница: 7 / 46

(8)

GND: Terminal for connection to station ground.

(9)

OUT: 3.5mm jack for output to micro2R

(10)

PADDLE 6.3mm (1/4") stereo female for paddle input.

TIP: DIT RING: DAH SLEEVE: GND

NOTE: The paddle sense can be reversed using Router settings

(11)

FOOTSW: input for optional foot switch (manual PTT)

(12)

LNA PTT: PTT output for controlling Low Noise Preamplifier or Receive antenna switching.

See PAPTT for jumper assignments and specifications.

4 - INSTALLATION

Installing DIGI KEYER II consists of several steps:

1) prepare DIGI KEYER II to work with your radio
2) installing the necessary driver software for your operating system
3) configure the microHAM CODEC and USB Device Router for Windows (if applicable).

Preparing DIGI KEYER II for Use

1. Remove the top cover from DIGI KEYER II and set the CAT jumpers as shown in the following chart.

The CAT interface jumpers must be configured to select the proper level for each radio type.

RS-232 levels: all transceivers with RS-232 CAT

(DB-9 or DB-25) interfaces.

IF-232 levels: Kenwood: TS-140, 440, 450, 680,

690, 711, 790, 811, 850, 940, 950

FIF-232 levels: Yaesu FT-100, 736, 747,

757GXII, 767, 817, 840, 857, 890, 897, 900,
980, 990, 1000, 1000D

CI-V levels: all Icom radios except IC-7800 and

IC-7700 using RS-232 and all TenTec rigs with
3.5mm connector

NOTE: the CAT interface is not configured at the factory.

Jumpers are shown configured for RS232 levels.

IF232

CI-V

FIF232

RS232

Содержание Digi Keyer II














































Результаты поиска

Содержание Digi Keyer II

Отзывы:

Похожие инструкции для Digi Keyer II

Бренды по названию

Популярные бренды

microHAM Digi Keyer II, Инструкция по эксплуатации

Результаты поиска

Содержание Digi Keyer II

Отзывы:

Похожие инструкции для Digi Keyer II

Бренды по названию

Популярные бренды