microHAM Digi Keyer II Скачать руководство пользователя страница 4

Страница: 4 / 46

Independent keying buffers for Power Amplifier and LNA switching

extended range solid state output for low voltage T/R lines or QSK

relay isolated output for vintage PA with negative voltage T/R lines

Bypass LNA before activating both PTT circuits for EME or scatter

Footswitch input with programmable functions

programmable PTT activation delay in 1ms steps

selectable muting of CW and/or FSK when footswitch is closed

Squelch input for signaling to computer

two inputs, one is active low, second is active high

ideal for Echolink and remote interfacing applications

No external power adapter (where the radio provides auxiliary power)

No noisy DC to DC converters

USB and Sound chip are powered from the computer USB port

Controller is powered from transceiver or transceiver power supply

Strong immunity from RFI

integrated chokes and filters for best RFI immunity

advanced shielding and circuit design to suppress RFI generation

Input/Output connectors

Computer: USB, Radio: DB15, Paddle: 6.3 mm, Sub RX: 3.5mm

Footswitch: RCA, PA PTT: RCA, LNA PTT: RCA, PTT IN: RCA,

PS/2: MiniDIN6, u2R: 2x3.5mm

Metal/Aluminum case, powder coated and silk screened

Free firmware/software upgrades via internet

165 mm (w) x 110 mm (d) x 44 mm (h)

2 - IMPORTANT WARNINGS

You must set the CAT level jumpers inside the DIGI KEYER II

before using it for the first time.

If you power DIGI KEYER II from an external power supply ALWAYS

check the polarity of the external 13.8 V supply.

DO NOT use the same external power supply for DIGI KEYER II and

your transceiver unless DK II receives power from the transceiver.

If your radio includes upgradeable firmware,

DO NOT perform any upgrade through DIGI KEYER II

Содержание Digi Keyer II














































Результаты поиска

Содержание Digi Keyer II

Отзывы:

Похожие инструкции для Digi Keyer II

Бренды по названию

Популярные бренды

microHAM Digi Keyer II, Инструкция по эксплуатации

Результаты поиска

Содержание Digi Keyer II

Отзывы:

Похожие инструкции для Digi Keyer II

Бренды по названию

Популярные бренды