background image

Master Rhino Manual_

March 2020.docx

 

March 20 

Page 25 of 38 

 

12. 

WARRANTY 

 

Products manufactured by MicroCool

 bear the following limited warranty: 

 

MicroCool warrants that the goods to be delivered will be of the kind and quality described in the sales order or 

contract, and will be free of defects in workmanship or material. Should any failure to conform to this warranty 

appear within the time limit stated below, after the initial date of delivery, the MicroCool shall, upon notification 

thereof, and written substantiation that the goods have been stored, installed, maintained and operated in 

accordance with the seller's recommendations and standard industry practice, correct such defect by suitable repair 

or replacement at its own expense. This warranty is limited to repairing or replacing products that the 

manufacturer's investigation shows were defective at the time of shipment by the manufacturer. An RMA number 

must be obtained from MicroCool

 before returning a product for warranty consideration or repair.   

 

Warranty period: 

 

One (1) year on all MicroCool manufactured goods

 

 

 

 

 

Two (2) years on coupled Weg motor and VF Drive 

 

 

 

 

The lesser of One (1) year or 4,000 hours use on pump head 

 

Notification Period:  

 

Notify MicroCool within 15 days of determining defect. 

Product Return Period:  Return defect product within 30 days to MicroCool 

All products subject to this warranty shall be returned for examination, repair or replacement, freight pre-paid to: 

 

MicroCool

 

 

72216 Northshore St. #103-104  

 

 

 

 

Phone#  

760-322-1111 

Thousand Palms, California 92276, USA  

 

 

 

FAX#      

760-343-1820 

 

E-mail address- 

[email protected]

 

  

 

 

 

Web site- www.microcool.com  

 

This warranty is exclusive and is in lieu of any warranty or merchantability, fitness for a particular purpose or other 

warranty of quality, whether express or implied, except of title and against patent infringement. Correction of non-

conformities, in the manner and for the period of time provided above, shall constitute fulfillment of all liabilities of 

the seller to the purchaser with respect to, or arising out of the goods, whether based on contract negligence, strict 

tort or otherwise. 

 

LIMITATION OF LIABILITY - Repair or replacement of defective products as provided above is the sole and 

exclusive remedy provided hereunder and the seller shall not under any circumstances be liable for special or con-

sequential damages such as, but not limited to, damage or loss of other property or equipment, loss of profits, or 

revenue, cost of capital, cost of purchased or replacement goods, or claims or customers of purchaser for service 

interruptions. The remedies of the purchaser set forth are exclusive and the liability of seller with respect to any 

contract, or anything done in connection therewith such as the performance or breach thereof, or from the 

manufacture, sale, delivery, resale, installation or use of any goods covered by or furnished under this contract 

whether arising out of contract, negligence, strict tort, or under any warranty, or otherwise, shall not, except as 

expressly provided herein, exceed the price of the goods upon which such liabilities based. This is the only warranty 

on any MicroCool

 product; no other writing or description in the literature shall be construed as a warranty. 

Products manufactured by other than MicroCool

 bear the following limited warranty: 

 

Seller warrants that the goods manufactured by others will conform to the description herein stated. No other 

warranty express or implied is made, and the warranty of the manufacturer is hereby assigned and transferred to 

the buyer. Furthermore, except for the manufacturer's warranty, if any, the products sold hereunder are sold as is. 

MicroCool

 is not liable for any incidental or consequential damages in connection with these products. 

 

In addition to all of the above, MicroCool

 accepts no liability if the system is used to dispense corrosive, toxic or 

other non-approved agents. MicroCool

 will not be responsible for poor water quality damage or nozzle blockage 

due to poor water quality. 

 

MicroCool

  

 

 

Содержание RHINO 15







































Отзывы: