Microchip Technology UCS81003 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 52

background image

UCS81003 EVALUATION

BOARD USER’S GUIDE



2014 Microchip Technology Inc.

DS50002300A-page 21

Chapter 3. Hardware Description

3.1

UCS81003 DEVICE

The UCS81003 provides a single USB port power switch for precise control of up to
3.0A continuous current (2.85A typical) with overcurrent limiting, dynamic thermal
management, latch/auto-recovery upon fault, selectable active low or high enable,
under and overvoltage lockout, and back-drive protection.
USB Charging Port profiles are integrated into the UCS81003 to assure compliance to
multiple standards. In addition to power switching and USB Charging Port profiling, the
UCS81003 provides automatic and configurable USB data line handshaking to enable
charging of USB-IF Battery Charging 1.2 (CDP or DCP modes), Chinese
Telecommunications Industry Standard YD/T 1591-2009, Apple

®

Inc., RIM

®

and many

other mobile devices.
The UCS81003 provides a device attachment detection output, as well as a dedicated
alert output, with current monitoring, charge rationing for controlled delivery of current
regardless of a host’s power state. When the limit is reached, the UCS81003 will
perform the user-programmed behavior (report and disconnect is the default).

3.2

EVALUATION BOARD POWER SOURCE

The UCS81003 has split power supply support:
• V

S

is the voltage input to Power Switch. This supply rail is required to charge the

portable device. V

S

source is selected by populating a jumper on J5 header, as

follows:

• V

DD

is the power supply for chip functionality. The UCS81003 Evaluation Board

contains two additional ICs, MCP2221 USB bridge and MCP23018 I/O expander,
which are also powered from the V

DD

supply rail. V

DD

source is selected by

populating a jumper on the J4 header, as follows:

Jumper

Position

Definition

1-2

V

S

is supplied from the external 5V power supply connected to J1 power jack.

2-3

V

S

is supplied from the V

BUS

pin of the J3 USB connector. Use this option

only if the USB host port can supply the charging current for the portable
device.

Jumper

Position

Definition

1-2

V

DD

is supplied from V

BUS

pin of the J2 USB connector. When using the

board in this configuration and the Attach Detection feature of the UCS81003
is used, the V

S

voltage must not exceed V

DD

+ 150 mV, as specified in the

data sheet.

2-3

V

DD

is connected to V

S

. This configuration is recommended when using the

Attach Detection feature. If the board is evaluated with a PC running the GUI,
then the V

S

must be supplied after the USB cable is plugged into the J2

connector.

«
...
19
20
21
22
23
...
»

Содержание UCS81003





















































Отзывы:

Нет отзывов

Похожие инструкции для UCS81003

Бренд: Abit Страницы: 104

Бренд: AOpen Страницы: 156

Бренд: Elitegroup Computer Systems Страницы: 82

Бренд: C&T Solution Страницы: 84

Бренд: Gigabyte Страницы: 96

Airborne WLNN-EK-DP55x

Бренд: B&B Electronics Страницы: 6

Бренд: Aaeon Страницы: 37

Бренд: Freescale Semiconductor Страницы: 28

Бренд: Inrevium Страницы: 57

Бренд: MSI Страницы: 22

EVAL-IH-R5IPB-A-V1

Бренд: Infineon Страницы: 34

8A 72QFN Series

Бренд: IDT Страницы: 29

Бренд: Safran Страницы: 29

Бренд: Avalue Technology Страницы: 80

Бренд: Supermicro Страницы: 229

Бренд: OLIMEX Страницы: 14

Бренд: MSI Страницы: 78

ZYNQ XC7Z020-1CLG484C

Бренд: National Instruments Страницы: 63

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды