manualshive.com logo in svg

Microchip Technology PIC16F716, Техническое описание

Поделиться
Скачать
Microchip Technology PIC16F716 Скачать руководство пользователя страница 15

 2003 Microchip Technology Inc.

Preliminary

DS41206A-page 13

PIC16F716

2.2.2.3

INTCON Register

The INTCON Register is a readable and writable
register which contains various enable and flag bits for
the TMR0 register overflow, RB Port change and
external RB0/INT pin interrupts.

 

REGISTER 2-3:

INTCON REGISTER (ADDRESS: 0Bh, 8Bh)      

Note:

Interrupt flag bits get set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit or the global
enable bit, GIE (INTCON<7>). User
software should ensure the appropriate
interrupt flag bits are clear prior to
enabling an interrupt.

R/W-0

R/W-0

R/W-0

R/W-0

R/W-0

R/W-0

R/W-0

R/W-x

GIE

PEIE

T0IE

INTE

RBIE

T0IF

INTF

RBIF

bit 7

bit 0

bit 7

GIE: Global Interrupt Enable bit

1

 = Enables all un-masked interrupts

0

 = Disables all interrupts

bit 6

PEIE: Peripheral Interrupt Enable bit

1

 = Enables all un-masked peripheral interrupts

0

 = Disables all peripheral interrupts

bit 5

T0IE: TMR0 Overflow Interrupt Enable bit

1

 = Enables the TMR0 interrupt

0

 = Disables the TMR0 interrupt

bit 4

INTE: RB0/INT External Interrupt Enable bit

1

 = Enables the RB0/INT external interrupt

0

 = Disables the RB0/INT external interrupt

bit 3

RBIE: RB Port Change Interrupt Enable bit

1

 = Enables the RB port change interrupt

0

 = Disables the RB port change interrupt

bit 2

T0IF: TMR0 Overflow Interrupt Flag bit

1

 = TMR0 register has overflowed (must be cleared in software)

0

 = TMR0 register did not overflow

bit 1

INTF: RB0/INT External Interrupt Flag bit

1

 = The RB0/INT external interrupt occurred (must be cleared in software)

0

 = The RB0/INT external interrupt did not occur

bit 0

RBIF: RB Port Change Interrupt Flag bit

1

 = At least one of the RB7:RB4 pins changed state (must be cleared in software)

0

 = None of the RB7:RB4 pins have changed state

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘

0

’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

Содержание PIC16F716































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды