manualshive.com logo in svg

Microchip Technology PIC16F716, Техническое описание

Поделиться
Скачать
Microchip Technology PIC16F716 Скачать руководство пользователя страница 14

PIC16F716

DS41206A-page 12

Preliminary

 2003 Microchip Technology Inc.

2.2.2.2

OPTION_REG Register

The OPTION_REG register is a readable and writable
register, which contains various control bits to configure
the TMR0 prescaler/WDT postscaler (single
assignable register known also as the prescaler), the
External INT Interrupt, TMR0 and the weak pull-ups on
PORTB.

REGISTER 2-2:

OPTION_REG REGISTER (ADDRESS: 81h)      

Note:

To achieve a 1:1 prescaler assignment for
the TMR0 register, assign the prescaler to
the Watchdog Timer.

R/W-1

R/W-1

R/W-1

R/W-1

R/W-1

R/W-1

R/W-1

R/W-1

RBPU

INTEDG

T0CS

T0SE

PSA

PS2

PS1

PS0

bit 7

bit 0

bit 7

RBPU: PORTB Weak Pull-up Enable bit

1

 = PORTB weak pull-ups are disabled

0

 = PORTB weak pull-ups are determined by alternate function or TRISBn bit value

bit 6

INTEDG: Interrupt Edge Select bit

1

 = Interrupt on rising edge of RB0/INT pin

0

 = Interrupt on falling edge of RB0/INT pin

bit 5

T0CS: TMR0 Clock Source Select bit

1

 = Transition on RA4/T0CKI pin

0

 = Internal instruction cycle clock (CLKOUT)

bit 4

T0SE: TMR0 Source Edge Select bit

1

 = Increment on high-to-low transition on RA4/T0CKI pin

0

 = Increment on low-to-high transition on RA4/T0CKI pin

bit 3

PSA: Prescaler Assignment bit

1

 = Prescaler is assigned to the WDT

0

 = Prescaler is assigned to the Timer0 module

bit 2-0

PS2:PS0: Prescaler Rate Select bits

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘

0

’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

Bit Value

TMR0 Rate

WDT Rate

000

1 : 2

1 : 1

001

1 : 4

1 : 2

010

1 : 8

1 : 4

011

1 : 16

1 : 8

100

1 : 32

1 : 16

101

1 : 64

1 : 32

110

1 : 128

1 : 64

111

1 : 256

1 : 128

Содержание PIC16F716































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды