Microchip Technology GridTime 3000 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 302

Microchip Technology GridTime 3000 Скачать руководство пользователя страница 71

Note:

Please note that TCP port number 8080 is 'open' on the administrator port. This port number is used by the Microchip
'upgrade and log retrieval' tool and will require a valid username and password to be entered before traffic is allowed
through the port.

The Microchip 'upgrade and log retrieval' tool is available on request in the event that an upgrade via the Clock
Management Tool is unsuccessful.

9.4.1

Static IP Address

This section describes how to provision the Admin Ethernet Port with a static IP Address.

1.

Set IP Addressing Mode to Static

Select 'STATIC' from the 'IPV4 METHOD' radio buttons, causing the static IP addressing settings to appear.

2.

Set Static IP Address

By default the static IP address is 192.168.1.200. To change this address, enter a different valid IP address in
the subnet your configuration PC is using.

Provisioning

©

2022 Microchip Technology Inc.

and its subsidiaries

Manual

DS00004572A-page 71

«
...
69
70
71
72
73
...
»

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды