manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 199

Click 'ADD' again to add another SNMP subscriber, click on the '02' tab under the 'ADD' button to navigate to
the settings for the new SNMP Subscription. The '01' tab contains the settings for the subscription that was
previously set up.

Repeat for as many subscriptions as are present on the network.

Tip: 

Click the red bin icon to remove an SNMP subscription.

7.

Save Settings

Click the 'SAVE' button to write the settings to the GridTime 3000.

A 'Saved!' notification will appear in the bottom right corner of the page indicating that the settings have
successfully been written to the GridTime 3000.

9.12.2 

Provisioning Syslog Notifications

This section describes how to provision Syslog notifications.

1.

Navigate to SNMP Config Window

Navigate to the SNMP Config window by clicking on the SNMP Config icon, then clicking the SNMP Config
settings bar.

 

Provisioning

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 199

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды