manualshive.com logo in svg

Microchip Technology GridTime 3000, Руководство по установке

Поделиться
Скачать
Microchip Technology GridTime 3000 Скачать руководство пользователя страница 19

...........continued

Name

Display

Clock
Information
Tab

CLOCK INFO

USB-C  IP 0.0.0.0

Firmware:

Admin IP 192.168.2.100

1.0b1.01

S/N CC000112

Shows the serial number, the firmware version and the IP address of the administration port.

Clock Power
Tab

CLOCK POWER

Reboot

Shutdown

Accessed by holding the middle front panel button when on any other tab. Press the left button to
restart the device, the right button to shut down, or the middle button to return to the main tab.

Note: 

 The shutdown is a software shutdown only, and will not switch off power to the device or its

internal components.

3.2 

Back Panel

This section describes the functionality on the GridTime

™

 3000 GNSS Time Server’s back panel.

Figure 3-2. GridTime 3000 Back Panel Features

1.

RJ-48C T1/E1/J1 ports (x2)

2.

BNC Ports 1-2 -Fixed frequency/TTL ports (x2)

3.

BNC ports 3-6 -AM IRIG/TTL ports (x4)

4.

BNC ports 7-8 -IRIG in/TTL out ports (x2)

5.

RJ-12 RS232 and RS422 serial string output ports (x1 of each)

6.

ST optical fiber output port (x2)

7.

HV MOSFET port — (x1)

8.

Form-C Alarm Relay Ports — (x2)

9.

TNC GNSS antenna port (x1)

10. Earth Stud
11. Power supply port(s) (up to x2)

 

Physical Overview

©

 2022 Microchip Technology Inc.

and its subsidiaries

 Manual

DS00004572A-page 19

Содержание GridTime 3000















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды