MICRO-EPSILON ILD 1320-10 Скачать руководство пользователя страница 52

Страница: 52 / 108

Page 52

Set Sensor Parameter

optoNCDT 1320

7.4.7.1

Zeroing, Mastering with Select Key

LED

state

Measuring

Green, red

, yellow,

depends on
measuring position

yellow

Key

select

Key

select

t 0



5 min

2 s

t 1

t 2

30 ms ... <3 s

The key

Select

locked according to
factory settings after
expiry of 5 min. You can
unlock the keylock e.g.
via the web interface,
see Chap.

7.6.3

Fig. 28 Flow chart for zeroing, mastering (key select)

LED

State

Measuring

Green, red, yellow,
depends on
measuring position

yellow

Key

select

t 0



5 min

2 s

t 1

t 2

5 s ... <10 s

The function Zeroing/Master-
ing can be used several times
in succession. Between
repetition of the function
Zeroing/Mastering a brake of
1 s is necessary. The func-
tion Zeroing/Mastering can
also be combined with the
multifunctional input.

Fig. 29 Flow chart for the return of zero setting and mastering

1) The key

Select

remains without effect since key lock is active.

2) The master value is not applied when LED

State

is red, flash frequency 3 Hz for 2 s.

Содержание ILD 1320-10













































































































Результаты поиска

Содержание ILD 1320-10

Отзывы:

Похожие инструкции для ILD 1320-10

Бренды по названию

Популярные бренды

MICRO-EPSILON ILD 1320-10, Инструкция по эксплуатации

Результаты поиска

Содержание ILD 1320-10

Отзывы:

Похожие инструкции для ILD 1320-10

Бренды по названию

Популярные бренды