manualshive.com logo in svg

Micro Autonomations Fan Controller v3, Руководство пользователя

Поделиться
Скачать
Micro Autonomations Fan Controller v3 Скачать руководство пользователя страница 11

 

Micro Autonomations LLC – Fan Controller v3 

11 

Document Rev 1.0 

Wiring the Fan 

The picture below shows the wiring of the fan plug.  Power to the fan should be supplied through a 50A 
minimum fuse/breaker, connected directly to a main power distribution point.   
  

 

Figure 7 - Fan plug wiring

 

Part numbers for the fan plug: 
 

Description 

Part Number 

Quantity Required 

Pin Housing/Bushing 

220 545 03 29 

1 

Large Wire 

000 540 36 05 

2 

Small Wire 

000 540 38 05 

2 

 

Recommended sensors 

Any generic GM type temperature sensor should work with the Controller.  We have currently tested 
with a TX3T two terminal temperature sensor.  The associated pigtail for this sensor is Pico 5615PT.  This 
sensor has a 3/8” NPT thread. 
 
Autometer #2258.  This is a single terminal 1/8” NPT sensor.  The sensor body must have a good 
connection to ground.  You may not be able to use sealant on the threads.   

 

 

Содержание Fan Controller v3




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды