background image

 

CWC-GASOLINE Operator's Manual   

                      

       

                  

 

        17  

SPECIFIC MAINTENANCE:  

EVAPORATIVE EMISSION COMPONENTS:
The unit you have purchased includes the following components that are in compliance with 2006 California 

Air Resources Board Evaporative Emission Standards;

1.   Fuel Hose
2.   Fuel Hose Fittings

These components should be inspected on a daily basis for cracks, leaks, and abnormal wear. If cracking, 

leaks or abnormal wear has occurred, the components should be replaced immediately.

ENGINE:

The engine instructions that accompany your unit detail specific procedures for maintenance of the engine. 

Following the engine manufacturer's recommendations will extend engine work life.
PUMP:

Change the pump oil after the first 50 hours of operation.  After initial change, every 3 months or 250 hour 

intervals are recommended.  If oil appears dirty or milky, changes may be required in greater frequency.  Use 

SAE20 or 30 Non-Detergent pump oil and fill only to the center of the oil sight glass or the "Full" mark on the 

dipstick.  DO NOT OVERFILL.
QUICK COUPLERS:

There is an o-ring seal inside the female quick-coupler.  This o-ring will deteriorate or, if the unit is allowed to 

pump without the high pressure hose attached, it may be blown out occasionally.  Simply insert a replace

-

ment o-ring to correct the leak.  (Additional o-rings can be purchased from your dealer.)
NOZZLES:

Water flow through the quick-connect spray nozzle will erode the orifice, making it larger, resulting in a pres

-

sure loss.  Nozzles should be replaced whenever pressure is less than 85% of the maximum. The frequency 

of replacement will depend upon such variables as mineral content in the water and number of hours the 

nozzle is used.
BELT TENSION ADJUSTMENT:

To maintain peak performance of your pressure washer, it may be 

necessary to adjust the belt tension on occasion.  Follow the proce-

dure outlined below.

1.  Remove the belt guard and loosen the two nuts on each side of 

the pump (Reference A).  There are a total of 4 nuts.

2.  Turn the cap screw (Reference B) clockwise until a 1/4 inch belt 

deflection is noticed between the pulleys.

3.  Tighten the side nuts (Reference A).
4.  Put a straight edge across both pulleys.  Pulley alignment is critical for proper performance and service 

life.  If necessary, loosen one set of pulley screws and adjust in or out to properly align.  Tighten the 

pulley screws and check the tension again.

5.  Replace the beltguard and tighten the fasteners securely.

WINTERIZING:

For storage and transportation purposes in subfreezing ambient temperatures, it will be necessary to winter

-

ize this unit.  This unit must be protected to the lowest incurred temperature for the following reasons:

1.  If any part of the pumping system becomes frozen, excessive pressure may build up in the unit which 

could cause the unit to burst resulting in possible serious injury to the operator or bystanders. 

2.  The pumping system in this unit may be permanently damaged if frozen. FREEZE DAMAGE IS NOT 

COVERED BY WARRANTY.

If you must store your unit in an area where the temperature may fall below 32°F, you can protect your unit by 

following the procedure outlined below.

1.  Gather the following items:

B

 A

STORAGE & MAINTENANCE

Содержание CWC GASOLINE Series













































Отзывы: