MHS Boilers XenoROL XR40 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 84

MHS Boilers XenoROL XR40 Скачать руководство пользователя страница 21

XenoROL®

21

CEILING HANGERSS

Drop rods and nuts are optional. The extension nut is

welded into the angle hanger upright during installation.

Cross pipes, V-brackets and flat strap connectors
are provided with ceiling hangers. Threaded 3/4" rod
and attaching nuts are available as an option. Bed
connectors are recommended with all ceiling hanger
applications.

If hanger uprights are field fabricated, they should be
a minimum of 1-1/2" x 1-1/2" x 3/16" angle.

After hanger uprights are installed and the heavy
extension nuts welded to angle hangers, thread the
drop rods into the extension nuts. Thread the jam
nuts and stop nuts on the drop rods far enough up
the rods to allow installation and adjustment of the
cross pipe.

While still on the floor, loosely attach cross pipe, V-
brackets, flat strap connectors and bed connector to
one end of a bed section. Hoist the bed section
between the drop rods guiding the rods through the
mounting holes in the cross pipe. Thread the weld
nuts on the drop rods to support the bed. Weld the
weld nuts to the drop rods to prevent loosening.
Hoist the next bed section into place and connect it
using the flat strap connectors and V-brackets.
Level the bed lengthwise and side to side by
threading the drop rods up or down by using a
wrench on the weld nuts. Tighten the jam nuts
against the extension nuts and the stop nuts against
the cross pipe. Continue for the length of the
conveyor.

WARNING

Consult the building architect or a structural
engineer regarding ceiling loading or
structural limitations of the building for sizing
header steel.

WARNING

Consult your distributor or a structural
engineer to determine what size hangers
should be used to support your maximum
anticipated load.

90480006rev092010

«
...
19
20
21
22
23
...
»

Содержание XenoROL XR40





















































































Отзывы:

Нет отзывов