STEP 6
SYSTEM DEVICE CONNECTION
After installing all devices in the system – each in the position specified in
STEP
4
– connect each device to the control unit as follows.
CAUTION!
– Incorrect connections can cause faults or hazards;
therefore ensure that the specified connections are strictly observed.
01.
Use a screwdriver to loosen the screw on the control unit cover and
extract the cover (
fig. 38
), to access the terminals for electrical con-
nections of the control unit.
02.
Use the same screwdriver to open the slots required for routing the
electric cables (
fig. 39
) from the various devices in the system.
03.
Then connect the electric wires of the system devices to the control
unit using the terminal board with five terminals (
fig. 39-a
).
CAUTION
– The section of electric cable connecting terminals 3
and 5 must only be removed if photocell installation is envis-
aged.
For correct connections, proceed as follows:
• To connect a pair of photocells with safety function
One or more pairs of photocells with a safety function must be installed on
the system. If several pairs of photocells are installed, these must be con-
nected
in series
, and the chain must be connected to terminals
3
and
5
on the control unit. The connect the power supply to terminals
2
and
3
(see example in
fig. 40-a
and
fig. 40-b
).
During the Closing manoeuvre, activation of these photocells causes
shutdown of the manoeuvre and immediate inversion of movement.
• To connect a NO type pushbutton used for manoeuvre control
An “
NO”
type pushbutton can be installed on the system, i.e. “
normally
open
” to control manoeuvres in “
step-step
” mode (for details on this
mode, see STEP 9). Connect this pushbutton to terminals
3
and
4
on the
control unit.
Note
– If several pushbuttons are installed to control manoeuvres, con-
nect these
in parallel
as shown in the example in
fig. 40-c
and
fig. 40-d
.
38
39
39-a
1
2
1
2
3
4
TX
RX
+ –
+ –
1
2
3
4
5
40-a
1
1
2
1
2
3
4
2
3
4
5
TX
RX
+ –
+ –
1
2
1
2
3
4
TX
RX
+ –
+ –
40-b
Input
S
TOP
0 VOL
T (–)
LINE 24 Vcc (+)
Input
S
TEP BY
S
TEP
Input PHOTO
1
2
3
4
5
1
2
3
4
5
40-c
English
English –
15
Содержание GDX01
